pushrod compatibility
-
- 356 Fan
- Posts: 61
- Joined: Mon Apr 07, 2008 9:03 am
- Location: Cape Cod, MA
pushrod compatibility
I am building a 546/2 engine with 1600cc cast iron Mahle cylinders, matching pistons, and 1956 1600N heads. I would like to use one of the three sets of pushrods I have: (1) the all steel variety with the wooden rattles inside. They are in good shape for their age, but only three rattle, suggesting it's a good idea to disassemble them, take out the dowels, clean up and reassemble. Problem is I don't want to risk screwing them up, not having done this before. (2) the all aluminum variety, in great shape, probably 912. (3) the hybrid super variety, also nice condition. I've searched the archives and there is a lot of info there, some of it contradictory. I seem to recall someone said the Al/Fe hybrid would work as a compromise with iron cylinders, and others have suggested OK to use all alloy ones but set the lash when hot.
Is there a consensus that the Al/Fe hybrid super ones would be OK with the iron cylinders? If not, is there someone who restores the iron ones?
Thanks, LLoyd
Is there a consensus that the Al/Fe hybrid super ones would be OK with the iron cylinders? If not, is there someone who restores the iron ones?
Thanks, LLoyd
- Phil Planck
- 356 Fan
- Posts: 2035
- Joined: Wed Mar 26, 2008 7:21 pm
- Location: NE Michigan, lower penn.
- David Jones
- Classifieds Moderator
- Posts: 7342
- Joined: Tue Mar 25, 2008 6:32 pm
- Tag: I wish I knew as much as I think I know.
- Location: Kentucky
Re: pushrod compatibility
Cool tool Phil, I like it. I shall make one for the engine currently being rebuilt and for the pushrods on the shelf.
If I had known I would live this long I would have pushed the envelope a little harder.
Cymru am byth
David Jones #9715
Cymru am byth
David Jones #9715
- Vic Skirmants
- Registry Hall of Fame
- Posts: 9304
- Joined: Tue Oct 27, 2009 5:02 pm
- Location: SE Michigan
- Contact:
Re: pushrod compatibility
1) That tool should work, but you need two lifters to use when tapping the end back on. One lifter to hold the pushrod, the second one to put over the end being installed.
2) 912 pushrods are stainless steel in the center, therefore not magnetic. If they are 912, use those. If long center is aluminum, don't use those.
3) Not sure which hybrid Super pushrods you have. Photo?
2) 912 pushrods are stainless steel in the center, therefore not magnetic. If they are 912, use those. If long center is aluminum, don't use those.
3) Not sure which hybrid Super pushrods you have. Photo?
- Martin Benade
- 356 Fan
- Posts: 12392
- Joined: Wed Nov 23, 2011 10:52 am
- Location: Cleveland, Ohio
Re: pushrod compatibility
Did all 912 s use ss pushrods?
Cleveland Ohio
62 Cabriolet
56 VW
02 IS 300
04 Sienna
62 Cabriolet
56 VW
02 IS 300
04 Sienna
- Vic Skirmants
- Registry Hall of Fame
- Posts: 9304
- Joined: Tue Oct 27, 2009 5:02 pm
- Location: SE Michigan
- Contact:
Re: pushrod compatibility
To the best of my knowledge, yes.
-
- 356 Fan
- Posts: 61
- Joined: Mon Apr 07, 2008 9:03 am
- Location: Cape Cod, MA
Re: pushrod compatibility
Thank you Vic, attached photo shows the two types in question. On the left is what I think is later S and S-90 type and on right what I think is the earlier type for those engines. Each has the center part made of the same material: non-magnetic and soft enough to scratch with a knife blade, hence alloy. I checked in HCP's book and he quotes you as saying not to use to all aluminum ones, but others would be OK. That's gotta be 40 yrs ago now! Still the same advice?
Also thanks to Phil. Nice solution! All I need to do is go get a 3/8' NPT coupling. I like using the original pushrods, after surgery, for this engine but I will keep an eye on how long before oil pressure comes up. But that would be the same no matter what pushrods.
LLoyd
Also thanks to Phil. Nice solution! All I need to do is go get a 3/8' NPT coupling. I like using the original pushrods, after surgery, for this engine but I will keep an eye on how long before oil pressure comes up. But that would be the same no matter what pushrods.
LLoyd
- Vic Skirmants
- Registry Hall of Fame
- Posts: 9304
- Joined: Tue Oct 27, 2009 5:02 pm
- Location: SE Michigan
- Contact:
Re: pushrod compatibility
Left pushrod has about the same expansion as a steel one. Right one is aluminum, therefore I do not recommend it for iron cylinders.
-
- 356 Fan
- Posts: 1260
- Joined: Thu Feb 05, 2009 8:13 pm
- Location: Texas Panhandle South Plains
Re: pushrod compatibility
+1
(it seems like I once read in an early "Up-fixin", that the ones as used in C engines, with the short AL centers, and long steel ends, would also work in any of the cast iron cylinders, as in the C P/C sets... )
Last edited by Mike Horton on Sat Feb 12, 2022 12:26 pm, edited 1 time in total.
Mike
- James Davies
- 356Talk Moderator
- Posts: 2959
- Joined: Thu Aug 15, 2013 9:15 am
- Location: Heidelberg, DE
Re: pushrod compatibility
The left "hybrid" steel/aluminum pushrod was ostensibly designed for use with cast iron cylinders introduced in 1957 for T2 production (from P*67001* onward according to The Specs)? These hybrid pushrods would have similar expansion to aluminum heads, aluminum case and cast iron cylinders.
That said, these pushrods are pictured in the 1956 workshop manual (page E40, figure 133). But this was, presumably, published before the introduction of cast iron cylinders in mid-1957. Also, the 1956 workshop manual only discusses the aluminum cylinders that were used on the 616/1 and 616/2 ( and 506/2 and 589/2) engines in 1956.
The 1957 parts catalog actually pictures these hybrid pushrods (Illustration 4, page 24) and labels them for cast iron cylinders on 616/1 and 616/2.
So what's the story?
That said, these pushrods are pictured in the 1956 workshop manual (page E40, figure 133). But this was, presumably, published before the introduction of cast iron cylinders in mid-1957. Also, the 1956 workshop manual only discusses the aluminum cylinders that were used on the 616/1 and 616/2 ( and 506/2 and 589/2) engines in 1956.
The 1957 parts catalog actually pictures these hybrid pushrods (Illustration 4, page 24) and labels them for cast iron cylinders on 616/1 and 616/2.
So what's the story?
-
- 356 Fan
- Posts: 1260
- Joined: Thu Feb 05, 2009 8:13 pm
- Location: Texas Panhandle South Plains
Re: pushrod compatibility
+1Vic Skirmants wrote: ↑Mon Feb 07, 2022 8:28 am Left pushrod has about the same expansion as a steel one. Right one is aluminum, therefore I do not recommend it for iron cylinders.
... this AL type PR is what was in my '62 S90 when I bought it in '85, but it also had near new C cast iron cylinders, and shortened 30° head angle piston skirts, another mismatch.
I substituted the 912 SS PR, per Vic, and as it had the faded black anodized S90 heads, I bought the 22° AA cast iron cylinder/hypereutectic cast pistons, in 86mm, which correctly matched the 22° heads. I set the C/R at just under the 9:1 nominal S90 spec, in deference to the erratic fuels of today out on the byways, a stock -102 Cam with fresh spherically reconditioned tappets, from Jacques, corrected the prior "assembler's" sins, and the engine is otherwise a 1720 S90, a good cruiser engine,
Mike
-
- 356 Fan
- Posts: 1260
- Joined: Thu Feb 05, 2009 8:13 pm
- Location: Texas Panhandle South Plains
Re: pushrod compatibility
the 2 C iron cylindered engines I had, the hybrid Al/steel PR were in both. Both the T5 iron cyl. Normals I had, and a spare N '59 A all had the steel PR, with the wood inside. My Friend Spike Jones, whose '58 A, originally a Normal, had been converted to a Super, in 1975, by Ray Litz, at CE, also paired the wood inserted steel PR with then new Mahle 82.5mm cast iron cyl., and cast S pistons, the early B "00" matched rods, and the old Performance Products type "Tri-com 105, RO 200.5 S spec cam. Paired with the original N BBBC 4th gear, it easily keeps up with other group cars.
Mike
- James Davies
- 356Talk Moderator
- Posts: 2959
- Joined: Thu Aug 15, 2013 9:15 am
- Location: Heidelberg, DE
Re: pushrod compatibility
Here's the story. Service Bulletin 17/55 indicates that the hybrid pushrods were introduced in mid-1955 on all engines (1300, 1300S, 1500, and 1500S), and continued to be used on the new 1600 and 1600S engines in Oct 1955. And of course they required different valve clearances. Purpose was to reduced valve gear noise.
It seems like whoever wrote Specs didn't bother to read old Porsche Service Bulletins. =)
- Attachments
-
- 55-17.pdf
- (178.68 KiB) Downloaded 62 times
- Spencer Harris
- 356 Fan
- Posts: 1149
- Joined: Thu Mar 27, 2008 12:39 pm
- Location: San Joaquin Valley, California
Re: pushrod compatibility
Wow! What a nice find, James.James Davies wrote: ↑Sun Nov 06, 2022 6:27 am Here's the story. Service Bulletin 17/55 indicates that the hybrid pushrods were introduced in mid-1955 on the 1300(S) and 1500(S) engines, and continued to be used on the new 1600 and 1600S engines in Oct 1955. And of course they required different valve clearances. Purpose was to reduced valve gear noise. It seems like whoever wrote Specs didn't bother to read old Porsche Service Bulletins. =)
Spencer Harris
San Joaquin Valley, CA.
San Joaquin Valley, CA.
-
- 356 Fan
- Posts: 1260
- Joined: Thu Feb 05, 2009 8:13 pm
- Location: Texas Panhandle South Plains
Re: pushrod compatibility
James, most of us back in the day, pre internet, had no access to the factory Service Bulletins... I think I first read about the compatibility of these PR in an "Up-Fixin" article written by Vic. Otherwise, we learned by our own experiences, as did I.
Thanks Vic !
Thanks Vic !
Mike