My SC coupe project. Made by hand…again.
- Michael Doyle
- 356 Fan
- Posts: 511
- Joined: Sat Mar 29, 2008 1:20 pm
- Location: Ventura, CA
Re: My SC coupe project. Made by hand…again.
You’re doing a fantastic job on your restoration. When interior time comes, I make the proper recreated Reutter Headliner for your car. The material is color matched very light grey with the elongated Diamond hole perforation pattern. Contact me for more info if interested. best/Michael
- Tom Perazzo
- 356 Fan
- Posts: 270
- Joined: Sun Jun 29, 2008 1:28 am
- Tag: It's only metal...
- Location: Huntington Beach, Ca
- Contact:
Re: My SC coupe project. Made by hand…again.
Thanks Michael, My car is a karmann. Is that pattern different?
Tom Perazzo
1964 SC Coupe (under restoration)
www.ZalexIndustries.com
- Tom Perazzo
- 356 Fan
- Posts: 270
- Joined: Sun Jun 29, 2008 1:28 am
- Tag: It's only metal...
- Location: Huntington Beach, Ca
- Contact:
Re: My SC coupe project. Made by hand…again.
Did ZF make replacement boxes with a slightly different casting?
I have one that has a metal tag on it with a date code of 566
Was that made is 66?
Just curious, I have a few other boxes too dated 63 and they are slightly different. More details in this video:
https://youtu.be/24YhU9gHm3A
I have one that has a metal tag on it with a date code of 566
Was that made is 66?
Just curious, I have a few other boxes too dated 63 and they are slightly different. More details in this video:
https://youtu.be/24YhU9gHm3A
Tom Perazzo
1964 SC Coupe (under restoration)
www.ZalexIndustries.com
- Tom Perazzo
- 356 Fan
- Posts: 270
- Joined: Sun Jun 29, 2008 1:28 am
- Tag: It's only metal...
- Location: Huntington Beach, Ca
- Contact:
Re: My SC coupe project. Made by hand…again.
Steering box now installed, adjusted, and looking good. Will add the locking plate tabs when doing final torque on the entire front suspension.
Full YouTube video here showing steering box rebuild and how I measured the tight spot torque
https://youtu.be/4XFIendCXH8
Full YouTube video here showing steering box rebuild and how I measured the tight spot torque
https://youtu.be/4XFIendCXH8
Tom Perazzo
1964 SC Coupe (under restoration)
www.ZalexIndustries.com
- Tom Perazzo
- 356 Fan
- Posts: 270
- Joined: Sun Jun 29, 2008 1:28 am
- Tag: It's only metal...
- Location: Huntington Beach, Ca
- Contact:
Re: My SC coupe project. Made by hand…again.
Ever wonder what the inside of the tunnel in the tunnel look like? I snuck a boroscope camera in there to check for sharp edges.
https://youtu.be/1pj-OBDK6X4
Cheers
Tom
Here's the full video and wire harness install.https://youtu.be/1pj-OBDK6X4
Cheers
Tom
Tom Perazzo
1964 SC Coupe (under restoration)
www.ZalexIndustries.com
-
- 356 Fan
- Posts: 2212
- Joined: Sat Oct 26, 2013 9:34 pm
- Location: Monterey, CA
Re: My SC coupe project. Made by hand…again.
Tom, I’ve enjoyed this thread for all the detail and beautiful work you have done. Did you post the work on the cowl or the exterior body in another forum? I have some damage to the interior cowl on my D, not quite sure how it got there, but it looks like fatigue cracks in the opening under the dash where the hinge comes through, so I would really enjoy seeing what you did to repair your cowl.Tom Perazzo wrote: ↑Mon Jan 27, 2020 3:28 pm My 356 is back home in my garage!
356 on trailer.jpg
356 back in garage.jpg
I bet you didn't know this would be a life long project did you?
Also, you refer to the use of osphoric acid several times. I am familiar with phosphoric acid, what is the difference? Are both acids readily available? I’ve used a metal etch product that contains dilute phosphoric acid that leaves a coating that stops flash rust.
- Tom Perazzo
- 356 Fan
- Posts: 270
- Joined: Sun Jun 29, 2008 1:28 am
- Tag: It's only metal...
- Location: Huntington Beach, Ca
- Contact:
T6 Gas Tank Tar Paper Sound Insulation Mat
I had a heck of a time installing the OEM asphalt based tap paper. Here is the second attempt.
Here's the install video:
https://youtu.be/ilNYn2x2mss
Tough to do on a cold day, so I ended making a makeshift disposable oven.Here's the install video:
https://youtu.be/ilNYn2x2mss
Tom Perazzo
1964 SC Coupe (under restoration)
www.ZalexIndustries.com
- Tom Perazzo
- 356 Fan
- Posts: 270
- Joined: Sun Jun 29, 2008 1:28 am
- Tag: It's only metal...
- Location: Huntington Beach, Ca
- Contact:
Karmann Engine Bay Sound Insulation
Moving on to the rear now.
I hate to cover up this cleanly painted engine bay. Here's the rear firewall pieces in position. The lower one gets glued and the upper one does not. I put some temporary push nuts in, but I'll replace with round once the interior is in. Still need to add the rear latch and shelf pieces and of course screw the side panels down.
Full YouTube vid here:
https://youtu.be/eEbxiw2Srrw
I hate to cover up this cleanly painted engine bay. Here's the rear firewall pieces in position. The lower one gets glued and the upper one does not. I put some temporary push nuts in, but I'll replace with round once the interior is in. Still need to add the rear latch and shelf pieces and of course screw the side panels down.
Full YouTube vid here:
https://youtu.be/eEbxiw2Srrw
Tom Perazzo
1964 SC Coupe (under restoration)
www.ZalexIndustries.com
- Tom Perazzo
- 356 Fan
- Posts: 270
- Joined: Sun Jun 29, 2008 1:28 am
- Tag: It's only metal...
- Location: Huntington Beach, Ca
- Contact:
Re: My SC coupe project. Made by hand…again.
Kinda hard to work with this authentic material, but it does look original.Tom Perazzo
1964 SC Coupe (under restoration)
www.ZalexIndustries.com
- Tom Perazzo
- 356 Fan
- Posts: 270
- Joined: Sun Jun 29, 2008 1:28 am
- Tag: It's only metal...
- Location: Huntington Beach, Ca
- Contact:
Re: My SC coupe project. Made by hand…again.
This car is finally back on four wheels again albeit temporarily.
I decided to inspect the transaxle and found a worn bearing, so the car has a temporary trans installed for now, but the assembly continues. Most of my work is covered in video format these days if your interested. It's a weekly vlog style.
https://youtu.be/37zLL8A8qwM
I decided to inspect the transaxle and found a worn bearing, so the car has a temporary trans installed for now, but the assembly continues. Most of my work is covered in video format these days if your interested. It's a weekly vlog style.
https://youtu.be/37zLL8A8qwM
Tom Perazzo
1964 SC Coupe (under restoration)
www.ZalexIndustries.com
- Phil Planck
- 356 Fan
- Posts: 2034
- Joined: Wed Mar 26, 2008 7:21 pm
- Location: NE Michigan, lower penn.
Re: My SC coupe project. Made by hand…again.
Looks great Tom. I think your going to beat me to the finish line.
Phil Planck
- Tom Perazzo
- 356 Fan
- Posts: 270
- Joined: Sun Jun 29, 2008 1:28 am
- Tag: It's only metal...
- Location: Huntington Beach, Ca
- Contact:
Re: My SC coupe project. Made by hand…again.
First drive in over 15 years!
Obviously not finished, but I just wanted it to move around the block under its own power. If you've been following my trans rebuild on YouTube, I'm proud to report that all the forward and reverse gears work beautifully.
I actually expected it to feel a little stiffer with new synchros, but it shifts great!
Obviously not finished, but I just wanted it to move around the block under its own power. If you've been following my trans rebuild on YouTube, I'm proud to report that all the forward and reverse gears work beautifully.
I actually expected it to feel a little stiffer with new synchros, but it shifts great!
Tom Perazzo
1964 SC Coupe (under restoration)
www.ZalexIndustries.com
- Mike Wilson
- Classifieds Monitor
- Posts: 11633
- Joined: Tue Apr 15, 2008 4:37 pm
- Location: SW Los Angeles
Re: My SC coupe project. Made by hand…again.
Congrats on the progress, Tom!
Mike
Mike
Mike Wilson
Lomita, CA
'63 B coupe
Lomita, CA
'63 B coupe
- Tom Perazzo
- 356 Fan
- Posts: 270
- Joined: Sun Jun 29, 2008 1:28 am
- Tag: It's only metal...
- Location: Huntington Beach, Ca
- Contact:
Re: My SC coupe project. Made by hand…again.
My brake lights weren't working correctly, so I did some troubleshooting and wiring research.
Looks like my master cylinder switch is bad, and I tried to install a 6V LED strip in the rear window, but Amazon sent me the wrong part.
Follow along on YouTube if you want, but here's a picture of the incandescent bulb on the left and and LED bulb on the right.
https://youtu.be/nt8svqRuyJY
Looks like my master cylinder switch is bad, and I tried to install a 6V LED strip in the rear window, but Amazon sent me the wrong part.
Follow along on YouTube if you want, but here's a picture of the incandescent bulb on the left and and LED bulb on the right.
https://youtu.be/nt8svqRuyJY
Tom Perazzo
1964 SC Coupe (under restoration)
www.ZalexIndustries.com
- Bill Lawless
- 356 Fan
- Posts: 955
- Joined: Mon Oct 25, 2010 10:17 pm
- Location: Northern Vermont
Re: My SC coupe project. Made by hand…again.
Nice work Tom..........
Thanks,
Bill
65' 356 SC Cab Irish Green
82' SC Targa
81 VW Westfalia with 2015 Forester Engine
BMW 64'-R50/2, 75'-BMW R90/6, 74' BMW R90/6, Yamaha BW350
Bill
65' 356 SC Cab Irish Green
82' SC Targa
81 VW Westfalia with 2015 Forester Engine
BMW 64'-R50/2, 75'-BMW R90/6, 74' BMW R90/6, Yamaha BW350