Incredibly hard cold start (50F), barely idles, then once warm it idles usually at 2,000, but sometimes drops to 1,400
-
- 356 Fan
- Posts: 86
- Joined: Thu Oct 10, 2019 12:03 pm
- Location: Seattle
Re: Incredibly hard cold start (50F), barely idles, then once warm it idles usually at 2,000, but sometimes drops to 1,4
>>>What distributer is fitted to your engine-correct unit has cast iron body and will have 022 //
Yes is ends with 022
>>>356s need to warm up before idling. Mine will idle at 800 after warm up. But will not idle cold. Or if set to idle at 1200 hot then they will idle cold at 800. This is because the manifolds need to warm up. You cannot get a stable idle above 1200 because the distributor advance begins at 1200. If the idle is set above 1200 or even at 1200 the idle speed will hunt up and down as the distributer advance changes. In order to get a nice stable 800 RPM warm idle, the tune up needs to be perfect and the plugs clean and gaped. I use the hand throttle on the As and warmup at 1700 RPM. I close the hand throttle on driving off, and then it idles at 800- till next time.
I don't have a hand throttle I believe as it's a 'C'... so is it the case that to expect it to start easily cold, and be able to idle at 800 with no driver input until it's warm just not in the cards / typical? I don't want to chase something that's not really fixable. It sounds like I should add a 6V electric fuel pump with 3lbs (does anyone know what one I should get, and where/how to install?), let the carbs fill up and then do the 3 pumps of the pedal and hold it down half and just keep the starter on until it fires; and then use my gas pedal to keep it going until warm enough to hold a 800rpm idle?
>>>>>With the engine off, look down the throats of the carbs and you should see two good streams of raw gas injected downward with each full stroke of the carb arm. This raw fuel is essential for the engine to start.
Yes, good streams on each carb. But even with the gas streaming still really hard to get it to start. But once it warms up it runs beautifully.
Yes is ends with 022
>>>356s need to warm up before idling. Mine will idle at 800 after warm up. But will not idle cold. Or if set to idle at 1200 hot then they will idle cold at 800. This is because the manifolds need to warm up. You cannot get a stable idle above 1200 because the distributor advance begins at 1200. If the idle is set above 1200 or even at 1200 the idle speed will hunt up and down as the distributer advance changes. In order to get a nice stable 800 RPM warm idle, the tune up needs to be perfect and the plugs clean and gaped. I use the hand throttle on the As and warmup at 1700 RPM. I close the hand throttle on driving off, and then it idles at 800- till next time.
I don't have a hand throttle I believe as it's a 'C'... so is it the case that to expect it to start easily cold, and be able to idle at 800 with no driver input until it's warm just not in the cards / typical? I don't want to chase something that's not really fixable. It sounds like I should add a 6V electric fuel pump with 3lbs (does anyone know what one I should get, and where/how to install?), let the carbs fill up and then do the 3 pumps of the pedal and hold it down half and just keep the starter on until it fires; and then use my gas pedal to keep it going until warm enough to hold a 800rpm idle?
>>>>>With the engine off, look down the throats of the carbs and you should see two good streams of raw gas injected downward with each full stroke of the carb arm. This raw fuel is essential for the engine to start.
Yes, good streams on each carb. But even with the gas streaming still really hard to get it to start. But once it warms up it runs beautifully.
- Martin Benade
- 356 Fan
- Posts: 12177
- Joined: Wed Nov 23, 2011 10:52 am
- Location: Cleveland, Ohio
Re: Incredibly hard cold start (50F), barely idles, then once warm it idles usually at 2,000, but sometimes drops to 1,4
It would be fine to try pumping the gas several more times. I have to pump mine a lot more than three times to get it to start, but once it’s running it runs great.
Cleveland Ohio
62 Cabriolet
56 VW
02 IS 300
04 Sienna
62 Cabriolet
56 VW
02 IS 300
04 Sienna
- Doug McDonnell
- 356 Fan
- Posts: 6061
- Joined: Sat Apr 05, 2008 8:21 am
- Location: Augusta,Michigan
Re: Incredibly hard cold start (50F), barely idles, then once warm it idles usually at 2,000, but sometimes drops to 1,4
Just to be clear in where we are. Very hard to start cold. 1. does it start easily if you try to start it after only 1 or 2 hours of cool down? or 2.It is very hard to start after 1-2 hours cool down.
1965 356C 2000 BMW 740i Sport 1967 Honda CL77 There is never enough time to do it right, but always enough time to do it over.
- Doug McDonnell
- 356 Fan
- Posts: 6061
- Joined: Sat Apr 05, 2008 8:21 am
- Location: Augusta,Michigan
Re: Incredibly hard cold start (50F), barely idles, then once warm it idles usually at 2,000, but sometimes drops to 1,4
Cheap priming pump bulb: https://porsche356registry.org/article/77 Electric pumps are frequently installed under the passengers side floor board. https://porsche356registry.org/article/78 Others install them on the right side of the diagonal member: https://www.stoddard.com/64450144106.html And newer solution by Ron LaDow of Precision Matters: https://precisionmatters.biz/auto-prime-primer-kit.php Of course you could also remove your mechanical pump and just use an electrical pump all the time, but then you would need a spare in your travel spare parts stash.
Last edited by Doug McDonnell on Wed Feb 12, 2020 12:45 am, edited 1 time in total.
1965 356C 2000 BMW 740i Sport 1967 Honda CL77 There is never enough time to do it right, but always enough time to do it over.
-
- 356 Fan
- Posts: 86
- Joined: Thu Oct 10, 2019 12:03 pm
- Location: Seattle
Re: Incredibly hard cold start (50F), barely idles, then once warm it idles usually at 2,000, but sometimes drops to 1,4
>>>Just to be clear in where we are. Very hard to start cold. 1. does it start easily if you try to start it after only 1 or 2 hours of cool down? or 2.It is very hard to start after 1-2 hours cool down.
Starts right up after an 1 or so...
>>>>Cheap priming pump bulb: https://porsche356registry.org/article/77
I love this idea... anyone have a downside to this option?
Starts right up after an 1 or so...
>>>>Cheap priming pump bulb: https://porsche356registry.org/article/77
I love this idea... anyone have a downside to this option?
- Doug McDonnell
- 356 Fan
- Posts: 6061
- Joined: Sat Apr 05, 2008 8:21 am
- Location: Augusta,Michigan
Re: Incredibly hard cold start (50F), barely idles, then once warm it idles usually at 2,000, but sometimes drops to 1,4
Then I would check your fuel pump suction and pressure. If OK do a priming bulb or pump. One of the reasons that owners of cars with Solex carbs have problems starting is that the accelerator pump system is misunderstood. On Zenith carbs when the float bowl has fuel so does the accelerator pump bowl. Not so on Solex carbs like you have in your SC. The bowl for that is filled only by vacuum on the backstroke of pumping the accelerator. Once it has filled then you get gas out of your enrichment tube when you pump the gas pedal. Which explains why those with Solex carbs do a lot more pumping than those with Zenith carbs on Normal or Super engines. Weak diaphragms for the enrichment circuit can also make it harder to fill that bowl requiring more pumping.
Last edited by Doug McDonnell on Wed Feb 12, 2020 1:03 am, edited 2 times in total.
1965 356C 2000 BMW 740i Sport 1967 Honda CL77 There is never enough time to do it right, but always enough time to do it over.
- Greg Scallon
- 356 Fan
- Posts: 781
- Joined: Thu Mar 27, 2008 1:12 pm
- Location: Los Altos, CA
Re: Incredibly hard cold start (50F), barely idles, then once warm it idles usually at 2,000, but sometimes drops to 1,4
Greg,
I'll let the others help out with the cold starting issues. I'm sure you'll get to the bottom of it. I will, however, chime in with a comment about the priming bulb idea. I installed a bulb in my speedster about 10 years ago and absolutely love it. Super easy install, can be removed in a jiffy if needed, requires no electricity, and it forces me to open the decklid before I go out, which lets me take a glance at my engine to make sure my fan belt's looking good and I'm not blowing oil all over the place. I still may install an electric priming pump someday, but as of now, I love the bulb. Go for it.
Good luck with your car.
Regards,
-Greg
I'll let the others help out with the cold starting issues. I'm sure you'll get to the bottom of it. I will, however, chime in with a comment about the priming bulb idea. I installed a bulb in my speedster about 10 years ago and absolutely love it. Super easy install, can be removed in a jiffy if needed, requires no electricity, and it forces me to open the decklid before I go out, which lets me take a glance at my engine to make sure my fan belt's looking good and I'm not blowing oil all over the place. I still may install an electric priming pump someday, but as of now, I love the bulb. Go for it.
Good luck with your car.
Regards,
-Greg
'58 Speedster
'56 VW Deluxe Microbus
'56 VW Deluxe Microbus
-
- 356 Fan
- Posts: 86
- Joined: Thu Oct 10, 2019 12:03 pm
- Location: Seattle
Re: Incredibly hard cold start (50F), barely idles, then once warm it idles usually at 2,000, but sometimes drops to 1,4
>>>Not so on Solex carbs like you have in your SC.
I have a 356C and Zenith carbs
I have a 356C and Zenith carbs
- Doug McDonnell
- 356 Fan
- Posts: 6061
- Joined: Sat Apr 05, 2008 8:21 am
- Location: Augusta,Michigan
Re: Incredibly hard cold start (50F), barely idles, then once warm it idles usually at 2,000, but sometimes drops to 1,4
Better yet. somewhere someone said 95% of carb problems are electrical. If fuel pump pressure is fine check points gap and timing. check distributor advance. Last resort if all else fine: https://www.youtube.com/watch?v=70dTCwNfQoM&t=69s But I emphasize last.
1965 356C 2000 BMW 740i Sport 1967 Honda CL77 There is never enough time to do it right, but always enough time to do it over.
- David Jones
- Classifieds Moderator
- Posts: 7323
- Joined: Tue Mar 25, 2008 6:32 pm
- Tag: I wish I knew as much as I think I know.
- Location: Kentucky
Re: Incredibly hard cold start (50F), barely idles, then once warm it idles usually at 2,000, but sometimes drops to 1,4
Go back and read 3rd post.
If I had known I would live this long I would have pushed the envelope a little harder.
Cymru am byth
David Jones #9715
Cymru am byth
David Jones #9715
- Vic Skirmants
- Registry Hall of Fame
- Posts: 9278
- Joined: Tue Oct 27, 2009 5:02 pm
- Location: SE Michigan
- Contact:
Re: Incredibly hard cold start (50F), barely idles, then once warm it idles usually at 2,000, but sometimes drops to 1,4
Doug; thanks for posting that explanation. Very well stated.Doug McDonnell wrote: ↑Wed Feb 12, 2020 12:51 am Then I would check your fuel pump suction and pressure. If OK do a priming bulb or pump. One of the reasons that owners of cars with Solex carbs have problems starting is that the accelerator pump system is misunderstood. On Zenith carbs when the float bowl has fuel so does the accelerator pump bowl. Not so on Solex carbs like you have in your SC. The bowl for that is filled only by vacuum on the backstroke of pumping the accelerator. Once it has filled then you get gas out of your enrichment tube when you pump the gas pedal. Which explains why those with Solex carbs do a lot more pumping than those with Zenith carbs on Normal or Super engines. Weak diaphragms for the enrichment circuit can also make it harder to fill that bowl requiring more pumping.
-
- 356 Fan
- Posts: 2506
- Joined: Thu Mar 27, 2008 9:14 am
- Tag: Official curmudgeon
- Location: Ft Collins CO
Re: Incredibly hard cold start (50F), barely idles, then once warm it idles usually at 2,000, but sometimes drops to 1,4
A lot of guesses flying around.
A few things to consider before changing anything:
Dwell
Timing
Adjustment of butterflies
Basic adjustment of mixture
Adjustment of throttle rods
Accelerator pump volume or at least some
Otherwise, you are pixxing into the wind so to speak.
A few things to consider before changing anything:
Dwell
Timing
Adjustment of butterflies
Basic adjustment of mixture
Adjustment of throttle rods
Accelerator pump volume or at least some
Otherwise, you are pixxing into the wind so to speak.
- Ken Lubke
- 356 Fan
- Posts: 290
- Joined: Fri Nov 21, 2008 1:40 pm
- Location: west mpls
Re: Incredibly hard cold start (50F), barely idles, then once warm it idles usually at 2,000, but sometimes drops to 1,4
Hey Mark,
They called them he/she’s didn’t they.?
Get your car back from Dave yet???
Kenny
They called them he/she’s didn’t they.?
Get your car back from Dave yet???
Kenny
-
- 356 Fan
- Posts: 86
- Joined: Thu Oct 10, 2019 12:03 pm
- Location: Seattle
Re: Incredibly hard cold start (50F), barely idles, then once warm it idles usually at 2,000, but sometimes drops to 1,4
Hi folks... I did as many suggested and started simple... I checked the point gap and it was super small... I reset to .016" and checked the timing after making a paint mark 19/64" to the right of OT; and noted the timing was spot on. I pumped the gas pedal 4 times and turned the key: it started almost immediately. I've adjusted the carbs with a unisyn to 900 rpm. I'll see tomorrow if I can reenact the starting. In any case, I guess too small a gap can make the car really hard to start but run OK when warm? Greg
- Bruce Smith
- 356 Fan
- Posts: 1624
- Joined: Sun Jun 19, 2011 9:47 am
- Location: Rochester, NY
- Contact:
Re: Incredibly hard cold start (50F), barely idles, then once warm it idles usually at 2,000, but sometimes drops to 1,4
Greg - Here's a write-up on dwell and timing from the Registry magazine a few issues back:
http://www.sparkingplugs.com/resources/ ... h+40-1.pdf
- Bruce
http://www.sparkingplugs.com/resources/ ... h+40-1.pdf
- Bruce
Bruce Smith