Removing the heater knob in a T-2 A

356 Porsche-related discussions and questions.
Post Reply
Message
Author
chris romney
356 Fan
Posts: 231
Joined: Tue Jul 29, 2008 1:13 pm

Removing the heater knob in a T-2 A

#1 Post by chris romney »

Can anyone tell me if the pin which holds the heater knob on in a T-2 A is tapered? I've had trouble getting the pin out so I can remove the knob. What's the secret? If anyone has any suggestions or insights, I'd appreciate hearing them. Thanks.

Chris
 

User avatar
John Lindstrom
356 Fan
Posts: 336
Joined: Mon Oct 23, 2017 9:51 am
Location: Stanford, Ca. USA

Re: Removing the heater knob in a T-2 A

#2 Post by John Lindstrom »

Is it rusted together like sometimes happens?

chris romney
356 Fan
Posts: 231
Joined: Tue Jul 29, 2008 1:13 pm

Re: Removing the heater knob in a T-2 A

#3 Post by chris romney »

Actually, it doesn't look that rusty, but the pin may not have ever been removed, so it's probably been in there for 60 years.
 

User avatar
John Lindstrom
356 Fan
Posts: 336
Joined: Mon Oct 23, 2017 9:51 am
Location: Stanford, Ca. USA

Re: Removing the heater knob in a T-2 A

#4 Post by John Lindstrom »

It’s a funny little pin in there. I can’t get mine off either, but it does not seemed rusted. Instead it feels loose. Very strange indeed. Somebody must know what the deal is with these. It’s almost as if they did not intend for it to ever come off.
Last edited by John Lindstrom on Wed Dec 13, 2017 10:24 pm, edited 1 time in total.

User avatar
Mike Wilson
Classifieds Monitor
Posts: 11490
Joined: Tue Apr 15, 2008 4:37 pm
Location: SW Los Angeles

Re: Removing the heater knob in a T-2 A

#5 Post by Mike Wilson »

Not tapered but likely frozen. Be really careful removing it as the knob is probably really brittle with age (first-hand experience). Use a good penetrant like Kroil. It might be easier to remove the spindle from the shifter base.

Mike
Mike Wilson
Lomita, CA
'63 B coupe

Brad Ripley
356 Fan
Posts: 4205
Joined: Tue Mar 25, 2008 9:28 pm

Re: Removing the heater knob in a T-2 A

#6 Post by Brad Ripley »

The pin is DIN 1475, 3 x 16 looks like below. As Mike suggests, you could unbolt the knob assembly, und or cut the heater cables and get the whole thing out on the bench.
Attachments
Heaterknob and shaft.jpg
Heaterknob and shaft.jpg (5.14 KiB) Viewed 905 times
DIN 1475 .jpg
DIN 1475 .jpg (8.65 KiB) Viewed 905 times

chris romney
356 Fan
Posts: 231
Joined: Tue Jul 29, 2008 1:13 pm

Re: Removing the heater knob in a T-2 A

#7 Post by chris romney »

Thanks Brad. I guess the pin wasn't designed to be removed.
 

Brad Ripley
356 Fan
Posts: 4205
Joined: Tue Mar 25, 2008 9:28 pm

Re: Removing the heater knob in a T-2 A

#8 Post by Brad Ripley »

Yes, Chris, I had the same idea about that type of pin -- but that's what the Porsche-printed parts catalogs say for the spec on that pin. The currently produced heater knob costs only $20, so you might have to sacrifice the original knob to take apart the assembly. Of course, you would have to put back together without breaking your new knob. So a simple roll pin could be used (DIN 1481) and lightly tapped into place.

Just curious -- why'd you want to take it apart in the first place?

User avatar
John Lindstrom
356 Fan
Posts: 336
Joined: Mon Oct 23, 2017 9:51 am
Location: Stanford, Ca. USA

Re: Removing the heater knob in a T-2 A

#9 Post by John Lindstrom »

Drill it out. Start with 1/16” bit to get it centered.

chris romney
356 Fan
Posts: 231
Joined: Tue Jul 29, 2008 1:13 pm

Re: Removing the heater knob in a T-2 A

#10 Post by chris romney »

Brad, you're going to laugh, but I had a nice set of square weave floor mats I was going to install, but the hole provided wasn't big enough to fit over the heater knob. I'll rethink what I'm going to do, but I won't be taking the knob off. Thanks again for your help.
 

Thom Fitzpatrick
356 Fan
Posts: 205
Joined: Mon Dec 12, 2016 6:15 pm
Location: Sacramento, CA

Re: Removing the heater knob in a T-2 A

#11 Post by Thom Fitzpatrick »

You could always do what I did: have the knob break apart in your hand the first time you turn on the heater for the cold season.

But seriously: I made (but currently can't find) a "press" for the heater pin using a small piece of rod and a C-clamp that I made when doing this on my '56 Karmann Ghia. The movable part of the clamp had the rod, which acts on the heater knob pin, and the static part had a hole for the pin to slide into as it's removed. I really only had to use the tool to pop the pin loose for the first 1/4" or so, and then I could drive the rest out with a drift.
1956 VW Single Cab
1957 Porsche 356A Sunroof Coupé
1957 VW 23-window Deluxe
1957 Mercedes Unimog 411
1963 Mercedes Unimog 404
1965 Jaguar E-Type
2003 BMW M3

Post Reply