Pre A windscreen wash pump - help !!

For Pre A discussions and questions
Post Reply
Message
Author
User avatar
JohnLiles
356 Fan
Posts: 206
Joined: Tue Dec 11, 2012 8:56 am
Location: London and NW England

Pre A windscreen wash pump - help !!

#1 Post by JohnLiles »

My '55 car has a manual pump under the dash , you push-pull the grey plastic knob until water squirts from the jets.

When I got the car the ( plastic) wash bottle was empty , I put some water in and pumped away and it worked !

some months later , having put proper wash solution in , would not work ,just some faint bubbling at the jets.
looked under the dash , shone torch on the clear plastic flexible tubing system , could see a lot of blackish particles , bit like soot , in all the flexibles , plus a lot of bubbles , and foaming a bit like a beer pour .

removed all the tubing , removed the pump , tried pumping water through. On the delivery stroke more black particles being pushed out the tubes connected to pump , both inlet and outlet . Also noted a bit of air bubbling out from where back lid fits on cylindrical casing . Assume that on suction stroke air is being pulled in through same place hence the two-phase 'beer pour' foam being delivered.

Have run some silicone sealant round the joint to see if that helps .

Question - is anyone familiar with the internals of these ( 60 year old ) pumps , should there be non return valve on inlet side to stop delivery back down inlet line - picture attached . I put a red hose on inlet side so I remember how to replumb it
Image
1957 'A' and 1955 'Continental Outlaw'

User avatar
Curt Dansby
356 Fan
Posts: 462
Joined: Fri Mar 14, 2008 9:50 am
Location: Charlotte, NC

Re: Pre A windscreen wash pump - help !!

#2 Post by Curt Dansby »

Hi John

I suspect this is your problem. You have a black bulb in the washer(some came with red bulbs) The bulb was dried out and brittle when you put fluid in the system and the fluid finished it off. The black particles are pieces of the bulb going downstream.
Take it apart from the hose end, not much to it. If it is in fact the bulb I know someone who can provide you a new one at a reasonable price.

Curt
Attachments
Bulb.jpg

User avatar
James Davies
356Talk Moderator
Posts: 2951
Joined: Thu Aug 15, 2013 9:15 am
Location: Heidelberg, DE

Re: Pre A windscreen wash pump - help !!

#3 Post by James Davies »

Here's a photo of what these typically look like on the inside after 60 years. They become very brittle. =)
Attachments
IMG_3121_SMALL.JPG

User avatar
JohnLiles
356 Fan
Posts: 206
Joined: Tue Dec 11, 2012 8:56 am
Location: London and NW England

Re: Pre A windscreen wash pump - help !!

#4 Post by JohnLiles »

Crikey ! Thanks guys , the pictures and graphic descriptions are really helpful !

Curt , I will make enquiries to see if can get a bulb supplied in UK , but if you can PM me the contact info for your source that would be great .
1957 'A' and 1955 'Continental Outlaw'

User avatar
JohnLiles
356 Fan
Posts: 206
Joined: Tue Dec 11, 2012 8:56 am
Location: London and NW England

Re: Pre A windscreen wash pump - help !!

#5 Post by JohnLiles »

Just to close this thread , Curt helped me to source a bulb , postage was the biggest expense but it arrived fast .

Today I got round to opening the pump case and seeing what was inside . A black rubber bulb was looking its age , not leaking but dispensing sooty water on demand. I had been puzzled by seeing absence of one way valves when testing the pump with old bulb in place , however after carefully washing out the outlet port it regained a one way behaviour.

I had some weeks previously had our local garage man blow air thru the wash jet nozzles , and he observed that they worked one way too , you could only blow out from inside the car .

I replaced the old black bulb with the new red one , and with the base cap and some short test hoses attached tested it in the kitchen sink , squeezing the bulb like an old fashioned Edwardian era car horn.
It worked , sucking thru the inlet and pushing out thru the outlet !

I now felt confident to reassemble all the flexible hoses and clamp the pump back in place under the dash , the longest run of hose delivering to the furthest nozzle had to be replaced as the sooty particles had settled in and could be seen but not moved by flushing , and too long to push a Qtip thru .

Everything seems to work fine again , and I have learned a bit more.....I wonder if it was covered in the workshop manual of the time ?
1957 'A' and 1955 'Continental Outlaw'

Andrea Scaioli
356 Fan
Posts: 20
Joined: Tue Nov 23, 2010 2:49 pm
Location: Italy
Contact:

Re: Pre A windscreen wash pump - help !!

#6 Post by Andrea Scaioli »

Hi Curt,

I have the same problem with my pre A wash pump , bulb is old and broken.
Please be so kind to let me know if and where is possible to find it.
Thank you very much for your help.

Andy

User avatar
Rick Albro
356 Fan
Posts: 330
Joined: Thu Mar 27, 2008 12:57 am

Re: Pre A windscreen wash pump - help !!

#7 Post by Rick Albro »

Andrea if you search on pipet bulbs you can then find by specification the one you need. Shipping will be more than the cost of the bulb. For your washer pump the inlet will need to be about 6mm and the 30 ml capacity one is pretty close to the right dimension. Shopping around last time I think I paid about $3 each and I bought several which have all now found new homes. For a one off purchase the cost in the range of under $10 is cheap. Do you have a date stamp and body style of your pump? I understand that Curt is one of the communities experts on restoring these pumps perhaps he has additional resources and suppliers. see also viewtopic.php?f=21&t=43193
Attachments
valves.jpg
pump apart.jpg
variety.jpg
washer date.jpg
bulb.jpg

Jeff Trevillyan
356 Fan
Posts: 41
Joined: Wed Mar 10, 2010 6:29 pm
Location: Lost Angeles, Kali

Re: Pre A windscreen wash pump - help !!

#8 Post by Jeff Trevillyan »

I obtained the bulb for my '53 from Curt. Perfect fit!
'53 Coupe #50431

Post Reply