Page 3 of 3

Re: 1956 356 "GT"

Posted: Wed Jul 17, 2019 8:02 am
by Vic Skirmants
Harlan Halsey wrote:
Wed Jul 17, 2019 1:24 am
Check WCSTA-06-56 T1 Post #44 for a picture of how I did it.

Yikes, Vic, I didn't know the Bosch solid state regulator case is hot! That seems crazy to me!
I agree, but that's the way it is; unless they have made a change.

Re: 1956 356 "GT"

Posted: Sat Aug 10, 2019 2:09 pm
by Trond Vidar
Verified that the new relay does not have a positive (hot) chassis anymore, that is rather fine.

The Zeniths were cleaned in ultrasound washer, gasoline, dismantled, blew all passages with air, set float height, set idle mixture but it run way to lean. It does have the correct jets for a S engine. I am still to test ignition at 30-ish degrees but at idle it is spot on.

If it does not run better I'll go back to Webers. The Venturis was rather stuck as well the mixture tubes. Did not measure the Venturis but will check upon dismantling. I will have to get the mixture tubes out and verify there is nothing clogged.

Have no idea when this engine ran well, have spent time on the carbs and ignition. The engine is noisy, I hope it is valve clearance or maybe a lean condition, worst case rod or main?

Youtube link to video running, seems way to lean as it hesitates to return to idle.

12 Volts and a new battery.
IMG_4578.jpg (230.01 KiB) Viewed 213 times
"Economy" fog lights, waiting for chromed KC Hilites, the cheapos go onto the Healey. :shock:
IMG_4579.jpg (257.43 KiB) Viewed 213 times
New classic style switches located in the ashtray opening, fogs, "ignition and electric fuel pump, the pump leaked and its just the filter for now until the new pump arrive.
IMG_4580.jpg (268.8 KiB) Viewed 213 times
Car is an "easy starter" but running way too lean.
IMG_4582.jpg (268.61 KiB) Viewed 213 times

Re: 1956 356 "GT"

Posted: Sun Aug 11, 2019 8:02 am
by Vic Skirmants
"Verified that the new relay does not have a positive (hot) chassis anymore, that is rather fine."

Did you check the outer case with the engine running?

Re: 1956 356 "GT"

Posted: Sun Aug 11, 2019 10:48 am
by Trond Vidar
Hm, don't remember but engine was maybe not running. Will verify after an attempt to dismantle / clean the carb. mixture tubes again.

btw: It's a brand new "Bosch Made in Mexico" regulator.

Re: 1956 356 "GT"

Posted: Mon Aug 12, 2019 7:55 am
by Vic Skirmants
When the engine is not running, the case is not "live" with voltage. It's only live when the generator is charging.

Re: 1956 356 "GT"

Posted: Tue Aug 13, 2019 12:17 pm
by Trond Vidar
Sure, got it! Yes I will check when the engine revs.

Btw: This was a nice surprise, seems like the best way to fix the wipers.

Re: 1956 356 "GT"

Posted: Wed Aug 14, 2019 3:26 pm
by Trond Vidar
You are right Vic, chassis is HOT as soon as the engine is running, the D+ is attached directly to chassis. Nice to know.

The new 12 V charging system seems good, playing around with lights and flashers etc but the enigne crank and start easy. I installed a WOSP Performance gear reduction starter, had to make a bump in the seat panel to make it fit, its not much just a couple mm deep in a large bump.

Carbs, the mixture tubes were bad, bead blasted them gently and put back. This solved the lean running condition. I adjusted the valves as well, most good but exhaust on 1 and 3 were too tight but maybe not open.

Finally I took the car out for a spin today, 5-6 km`s shakedown, new set of tasks, there are problems to resolve.

* The 60 mm studs I installed for the Technomagnesio rims touch brakeshoes when braking. The head of these were slightly larger than the old ones. The studs are OEM porsche. Grind them sligthly maybe?
* Loose front wheel bearings.
* Sloppy steering box

I have had the car since what, 2011 maybe and the seller had it stored years before that? This is a good day.
IMG_4602.jpg (492.64 KiB) Viewed 71 times

Re: 1956 356 "GT"

Posted: Thu Aug 15, 2019 2:47 pm
by Trond Vidar
Another 10 km trip today, fixed the brake noise with a thin spacer to "shorten" the brake shoe holding pin. The cup for the brake shoe retaining pin will be changed to the newer version, the originals seem deeper than necessary, its actually the retaining pin cup/clip that get in contact with studs when braking.

Steering box is definitely bad, its wandering and I have to get a rebuilt one and a VW pitman arm or perhaps rebuild the box but are there any sources for parts? (Original 1956 box)

Engine noise is still there and I wont drive it more until I find the source. At least it's not the fan, generator is new and I took off the belt and spun it to verify it is still silent. I'll check the rockers and stands for problems, if they are good the engine will have to go out during winter. Cant think about anything else that could be clunking but rods or mains.

It will be more inspiring to finish interior and electrical work this winter, until yesterday I had not driven the car more than 100 meters. Gearbox was fine, suspension good, brakes have a lot of bite in them and the car will be fine once engine noise and steering is taken care of.

The (old car) driving season usually end mid october over here and I'll spend the time on the '63 coupe. It need be driven more.

15 Aug 2019, more than. 8 years since my first post. Slate gray '56, admit to decal tuning but I want it to look like a classic road racer.
IMG_4610.jpg (494.91 KiB) Viewed 46 times
IMG_4608.jpg (504.34 KiB) Viewed 46 times