Raised rectangular area on 1959 356A Lower Tail Panels Info

For those who obsess about exactly how their 356 left the factory!
Message
Author
User avatar
Vic Skirmants
Registry Hall of Fame
Posts: 9279
Joined: Tue Oct 27, 2009 5:02 pm
Location: SE Michigan
Contact:

Re: Raised rectangular area on 1959 356A Lower Tail Panels Info

#16 Post by Vic Skirmants »

Brett Johnson wrote: Wed Apr 17, 2019 4:12 pm So far, no Conv. Ds have them.
That's because Drauz didn't get those parts.

User avatar
Harlan Halsey
356 Fan
Posts: 2339
Joined: Fri Mar 02, 2012 2:05 pm
Location: No Cal SF Peninsula

Re: Raised rectangular area on 1959 356A Lower Tail Panels Info

#17 Post by Harlan Halsey »

I have always wondered a bit about how Porsche dealt with it's several main suppliers. I assume that there was only one supplier for all the sheet metal pieces, that Reutter, Karman, Drauz, etc., ordered panels directly from the same supplier, despite slight differences in the assembled bodies. (I think I have read that there are differences in the windshield gaskets between Reutter and Karman bodies.) Porsche itself must have also ordered and stocked repair panels. Years ago I saw several of those odd rear panels in stock at Carlson Porsche in Palo Alto. I suspect that there was a mix up over the backup light introduction which resulted in those panels with the incomplete backup light mount. Perhaps by that time Drauz already had sufficient supply to complete their order. Do the odd panels appear on both Reutter and Karman built cars?
Last edited by Harlan Halsey on Sat Apr 20, 2019 8:47 pm, edited 1 time in total.

User avatar
Vic Skirmants
Registry Hall of Fame
Posts: 9279
Joined: Tue Oct 27, 2009 5:02 pm
Location: SE Michigan
Contact:

Re: Raised rectangular area on 1959 356A Lower Tail Panels Info

#18 Post by Vic Skirmants »

Karmann built no cars during that period.

Max Handley
356 Fan
Posts: 951
Joined: Wed Apr 02, 2008 11:52 am

Re: Raised rectangular area on 1959 356A Lower Tail Panels Info

#19 Post by Max Handley »

7245AE28-E0BC-4FE8-94CA-56B1A09DBBF4.jpeg
7245AE28-E0BC-4FE8-94CA-56B1A09DBBF4.jpeg (131.49 KiB) Viewed 3008 times
Cab. 151763 mfg. date 2/59
No raised area
 Contact email Spyderwerks@comcast.net

David Pateman
356 Fan
Posts: 151
Joined: Sun Mar 13, 2016 9:36 pm
Location: Canada

Re: Raised rectangular area on 1959 356A Lower Tail Panels Info

#20 Post by David Pateman »

Back about 1980 I had a pair of Conv D's. I was assembling the parts required for the restoration and went down to Stoddard's. Chuck himself assisted me in picking the parts. For the door latch posts, he dropped the stairway to the loft and disappeared for several minutes, but returned with a pair of NOS pieces. He said that these were unique to the D, and if I had not actually been there the shop would have shipped Cab reproductions (and these would have required modifications). The panels also had inner panels attached to them, and both had Drauz tags. This leads me to think that some or many panels may have been made by the suppliers and not from a common panel supplier.
Contact for Kardex

Ron Guest
356 Fan
Posts: 15
Joined: Thu Apr 17, 2008 3:07 pm
Location: Sonoma, CA

Re: Raised rectangular area on 1959 356A Lower Tail Panels Info

#21 Post by Ron Guest »

My D, number 86717, has a very clean, unmolested and undamaged rear panel and it DOES have the raised rectangular area on the lower rear. There is no evidence of damage and/or repair to the underlying structure and when it was down to bare metal it clearly looked like a factory panel. Don’t know how that fits in the “No Conv. Ds have them” discussion, but it is what it is.
Ron Guest
'64 C-#130257
'59 Convert D-#86717
Reg #17868

User avatar
Vic Skirmants
Registry Hall of Fame
Posts: 9279
Joined: Tue Oct 27, 2009 5:02 pm
Location: SE Michigan
Contact:

Re: Raised rectangular area on 1959 356A Lower Tail Panels Info

#22 Post by Vic Skirmants »

What was the build date for your car?

User avatar
Brett Johnson
Registry Hall of Fame
Posts: 641
Joined: Thu Mar 27, 2008 12:37 pm
Location: Indianapolis

Re: Raised rectangular area on 1959 356A Lower Tail Panels Info

#23 Post by Brett Johnson »

86717 = July 17, 1959

Coupes and cabriolets got them April/May 1959.
Brett Johnson

Ron Guest
356 Fan
Posts: 15
Joined: Thu Apr 17, 2008 3:07 pm
Location: Sonoma, CA

Re: Raised rectangular area on 1959 356A Lower Tail Panels Info

#24 Post by Ron Guest »

Correct, July 17, 1959.
Ron Guest
'64 C-#130257
'59 Convert D-#86717
Reg #17868

Steve Douglas
356 Fan
Posts: 1109
Joined: Wed Apr 02, 2008 9:49 pm
Location: Gilroy, CA

Re: Raised rectangular area on 1959 356A Lower Tail Panels Info

#25 Post by Steve Douglas »

My Coupe was built and delivered also on July 17, 1959. 108438

Drew Saunders
356 Fan
Posts: 46
Joined: Thu Jun 30, 2011 3:09 pm
Location: Surrey UK

Re: Raised rectangular area on 1959 356A Lower Tail Panels Info

#26 Post by Drew Saunders »

Hi Brett
Here are a few more data points for you.
1959 RHD 106621 no raised area
1959 RHD 107123 no raised area
1959 RHD 107156 no raised area, but soon to receive one (sorry Brett if this confuses future editions of your book)
1959 Convertible D 86254 no raised area
1959 Convertible D 86490 no raised area
Here is a rear end that I’ll be using on 107156, it must have been an NOS panel that was poorly welded onto the rear of a T2 in the past, it was only tack welded in a few spots around the lower engine lid opening not factory spot welded.
DSCF8317_sml.JPG
DSCF8317_sml.JPG (578.47 KiB) Viewed 2180 times
DSCF8319_sml.JPG
DSCF8319_sml.JPG (794.11 KiB) Viewed 2180 times
There are a few interesting details:
The lower edge is not bent vertically downward like T2 rear and front panels but is bent inward.
The exhaust cut outs seem to be narrower than the opening on my other 59’s.
And the PORSCHE badge mounting holes and inner fixing plate is for the longer ‘B’ badge.
Regards
Drew
United Kingdom
1944 Type 82 Kubelwagen (Sold)
1959 RHD Coupe (Sold)
1959 LHD Convertible D (Sold)
1959 RHD Coupe (under restoration)
1959 LHD Convertible D (awaiting restoration)

User avatar
John Hearn
356 Fan
Posts: 627
Joined: Thu Jul 31, 2008 9:26 am
Tag: Porsche is a two sylable word!
Location: Colchester, Great Britain

Re: Raised rectangular area on 1959 356A Lower Tail Panels Info

#27 Post by John Hearn »

My '59 Coupe 108707 Born 11th August, belated Happy 60th Birthday has raised area.
KTF
John

Post Reply