Porsche356registry.org
http://forum.porsche356registry.org/

Gebi Bolts
http://forum.porsche356registry.org/viewtopic.php?f=13&t=44018
Page 1 of 1

Author:  Michael Gregg [ Tue May 30, 2017 9:50 pm ]
Post subject:  Gebi Bolts

I can't find any reference to Gebi hardware on the forum. I've found a few so far used on my '64 356C as link pin pinch bolts and tie rod clamp bolts. I have found some references over on The Samba site. Anyone else seen these bolts on their 356?

Attachments:
Zn7udoo4TiS4EYPYWlJslw_thumb_331a 2.jpg
Zn7udoo4TiS4EYPYWlJslw_thumb_331a 2.jpg [ 169.36 KiB | Viewed 1060 times ]

Author:  Brad Ripley [ Sun Jun 04, 2017 11:42 pm ]
Post subject:  Re: Gebi Bolts

GEBI has been around since 1885 and still going -- see http://bierbach-gmbh.de/englisch/company.php

Author:  Martin Benade [ Mon Jun 05, 2017 12:15 am ]
Post subject:  Re: Gebi Bolts

Has anyone else found their bolts on a 356? I have not heard of that brand myself.

Author:  Michael Gregg [ Sat Jun 17, 2017 8:58 am ]
Post subject:  Re: Gebi Bolts

I've also found some NEDUR 8G bolts used on the rear torsion bar bushing cover.

Author:  Brad Ripley [ Mon Jun 19, 2017 12:30 am ]
Post subject:  Re: Gebi Bolts

Company that once used trademark NEDUR is Koninklijke Nedschroef Holding B.V., in the Netherlands. See their website: https://www.nedschroef.com/en/about_nedschroef/history/

Author:  Jon Bunin [ Wed Jun 28, 2017 10:41 pm ]
Post subject:  Re: Gebi Bolts

It's not a brand that I see often, especially on a 356.
I was searching through my photos for other reasons, and found this- a 935 transmission that I rebuilt recently...

Attachments:
DSCN0381.JPG
DSCN0381.JPG [ 635.93 KiB | Viewed 666 times ]
DSCN0374.JPG
DSCN0374.JPG [ 633.07 KiB | Viewed 666 times ]

Author:  Etienne Kerkhoffs [ Tue Jul 11, 2017 10:53 am ]
Post subject:  Re: Gebi Bolts

My windshield wiper mechanism (356 T2) has Gebi bolts:

Attachments:
P8082000.JPG
P8082000.JPG [ 755.9 KiB | Viewed 516 times ]
P8081997.JPG
P8081997.JPG [ 840.59 KiB | Viewed 516 times ]

Author:  Charles H Jacobus [ Tue Jul 11, 2017 11:30 am ]
Post subject:  Re: Gebi Bolts

Jon:
The quality of the wire raps on those safety wired bolts looks like you might have been an aircraft mechanic, nice!

ChuckJ

Author:  Jon Bunin [ Wed Jul 12, 2017 2:50 am ]
Post subject:  Re: Gebi Bolts

Thank you Chuck. I've worked on various things with wings, but nothing designed to leave the ground.

Author:  Wes Bender [ Thu Jul 13, 2017 11:04 am ]
Post subject:  Re: Gebi Bolts

+1 Jon. Safety wiring like that is a sign of attention to detail.

Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/