Link Pins loosen up
-
- 356 Fan
- Posts: 4207
- Joined: Tue Mar 25, 2008 9:28 pm
Re: Link Pins loosen up
In my experience one should always check the stub axel for straightness of the axle and the angle of the steering arm. Porsche tool P 69 is applicable for checking of parts of the axle; see photo below. The two bushing in the photo are adaptors for 356C axles. Also, another Porsche tool, P 70, is useful to check for parallelism and twist; I don't have a photo of that tool. All this can be found on pages S18 thru S22 of the B/C Workshop Manual.
I bigger problem is twisted and bent C-links. The C-link should be checked. There was not a Porsche tool for that but you could make one. I can send a photo of a homemade version of that tool if someone is interested. I guess as many as 20% of c-links are bent. You cannot straighten them with a big bar or hammer. Buy a new one. BTW, VW links must be machined to be used in the Porsche application.
I bigger problem is twisted and bent C-links. The C-link should be checked. There was not a Porsche tool for that but you could make one. I can send a photo of a homemade version of that tool if someone is interested. I guess as many as 20% of c-links are bent. You cannot straighten them with a big bar or hammer. Buy a new one. BTW, VW links must be machined to be used in the Porsche application.
- Attachments
-
- Porsche tool P69.jpg (165.05 KiB) Viewed 1385 times
- Juha Vane
- 356 Fan
- Posts: 314
- Joined: Tue Jul 01, 2008 3:06 pm
- Location: Sumiainen, Finland
Re: Link Pins loosen up
Noted also loose link pins in my 356.
Brad, please send me a photo of the tool and could you tell
what need to be machined in VW links if it is not very obvious.
TIA vane@rennlist.com
Brad, please send me a photo of the tool and could you tell
what need to be machined in VW links if it is not very obvious.
TIA vane@rennlist.com
KTF,
Juha Vane
Finland
'59 308
'63 356
'85 911
Juha Vane
Finland
'59 308
'63 356
'85 911
-
- 356 Fan
- Posts: 1805
- Joined: Thu Oct 15, 2009 11:06 pm
- Location: Vista, CA
Re: Link Pins loosen up
Here are both tools...Brad Ripley wrote: ↑Tue Nov 19, 2019 8:02 pm... Also, another Porsche tool, P 70, is useful to check for parallelism and twist; I don't have a photo of that tool ...
- Attachments
-
- DSCN1255.JPG (725.51 KiB) Viewed 1363 times
Jon Bunin
- Harlan Halsey
- 356 Fan
- Posts: 2373
- Joined: Fri Mar 02, 2012 2:05 pm
- Location: No Cal SF Peninsula
Re: Link Pins loosen up
It won't be long before someone points out that the P 70 trailing arm tool doesn't work very well for the lower arm because the sway bar mount interfers with the long pin. We get around that in several ways, but it has ocurred to me that one of those laser bore sight cartriges could be mounted in a shortened bar and a target put on the other alignment pad.
As for straightening the C links, Ron does that as a matter of course. That's just part of the king pin/link pin bushing job.
BTW: Doug at Techcraft line hones the new king pin bushings for us. That does a better job than the VW reamer. Not that the reamer doesn't do a good enough job, but if you've got the equipment.....
As for straightening the C links, Ron does that as a matter of course. That's just part of the king pin/link pin bushing job.
BTW: Doug at Techcraft line hones the new king pin bushings for us. That does a better job than the VW reamer. Not that the reamer doesn't do a good enough job, but if you've got the equipment.....
- Joris Koning
- 356 Fan
- Posts: 2518
- Joined: Thu Mar 27, 2008 12:38 pm
- Location: Netherlands
Re: Link Pins loosen up
Is there anybody out there who straightens control arms? I have heard of this being done. With the supply of straight arms getting less and less it would be a worthwhile service to the hobby
'56 Coupe
'57 Coupe
'59 Cab
'60 Coupe
'57 Coupe
'59 Cab
'60 Coupe
-
- 356 Fan
- Posts: 1805
- Joined: Thu Oct 15, 2009 11:06 pm
- Location: Vista, CA
Re: Link Pins loosen up
Not true Harlan, the sway bar mount does not interfere. When the rubber bushing is removed, the pin passes through the mount.Harlan Halsey wrote: ↑Wed Nov 20, 2019 4:04 am It won't be long before someone points out that the P 70 trailing arm tool doesn't work very well for the lower arm because the sway bar mount interfers with the long pin...
Jon Bunin
-
- 356 Fan
- Posts: 1805
- Joined: Thu Oct 15, 2009 11:06 pm
- Location: Vista, CA
Re: Link Pins loosen up
Example from the manual, on a lower arm...Jon Bunin wrote: ↑Wed Nov 20, 2019 4:55 amNot true Harlan, the sway bar mount does not interfere. When the rubber bushing is removed, the pin passes through the mount.Harlan Halsey wrote: ↑Wed Nov 20, 2019 4:04 am It won't be long before someone points out that the P 70 trailing arm tool doesn't work very well for the lower arm because the sway bar mount interfers with the long pin...
- Attachments
-
- DSCN1256.JPG (722.43 KiB) Viewed 1349 times
Jon Bunin
- Al Zim
- 356 Fan
- Posts: 4377
- Joined: Thu Mar 27, 2008 12:37 pm
- Location: FT.WORTH/DALLAS TEXAS
- Contact:
Re: Link Pins loosen up
The tool to check the offset on the "C" carrier is a VW 259. Remember you can easily bend the "C" carrier if you are using a heavy press to remove the king pin. I have mad a tool to TRY and straighten the trailing arms. One of the tools is a a solid thick round 6 foot steel rod. When I was 300 pounds I was able to do some small straightening. Now that I am 200 pounds that activity seems to have alluded me. al zim
www.allzim.com
356 Parts and Services
www.facebook.com/ZimsAuto/
www.instagram.com/zims_autotechnik/
356 Parts and Services
www.facebook.com/ZimsAuto/
www.instagram.com/zims_autotechnik/
- Martin Benade
- 356 Fan
- Posts: 12388
- Joined: Wed Nov 23, 2011 10:52 am
- Location: Cleveland, Ohio
Re: Link Pins loosen up
My old-school European mentor would heat and straighten most any suspension part, with good results. I always wondered what that did to the strength, but he never had a comeback.
Cleveland Ohio
62 Cabriolet
56 VW
02 IS 300
04 Sienna
62 Cabriolet
56 VW
02 IS 300
04 Sienna
- David Jones
- Classifieds Moderator
- Posts: 7342
- Joined: Tue Mar 25, 2008 6:32 pm
- Tag: I wish I knew as much as I think I know.
- Location: Kentucky
Re: Link Pins loosen up
The "C" link or "dogbone" king pin carrier is a VW part that is machined on the inside face where it contacts the face of the suspension arms and quite frankly I do not understand why Porsche chose to do that. The only difference that becomes apparent on installation is that one must now use the Porsche rubber seal over the shims instead of the VW "O" ring that is I guess installed on the link pin to prevent incursion of water to the shim pack and link pin bushing. I have on more than one occasion used the VW part out of sheer laziness when I had more than a few VW parts lying around as I used to bend them occasionally when racing the F Vee. There may be a good reason not to use the VW part unmodified but someone with a higher pay grade will have to tell me why.
My to do list has the left side "C" link listed as an item to be taken care off this winter so I am still running an unmodified one as of now. I have one ready to go but for machining off the inside face. I can post a picture if anyone needs it.
My to do list has the left side "C" link listed as an item to be taken care off this winter so I am still running an unmodified one as of now. I have one ready to go but for machining off the inside face. I can post a picture if anyone needs it.
If I had known I would live this long I would have pushed the envelope a little harder.
Cymru am byth
David Jones #9715
Cymru am byth
David Jones #9715
- Vic Skirmants
- Registry Hall of Fame
- Posts: 9303
- Joined: Tue Oct 27, 2009 5:02 pm
- Location: SE Michigan
- Contact:
Re: Link Pins loosen up
Porsche used the VW C link with no mods through 1955.
- David Jones
- Classifieds Moderator
- Posts: 7342
- Joined: Tue Mar 25, 2008 6:32 pm
- Tag: I wish I knew as much as I think I know.
- Location: Kentucky
Re: Link Pins loosen up
Vic, does that mean that they just used a VW stub axle complete and the only difference at that time to a VW was the larger aluminum drum?
If I had known I would live this long I would have pushed the envelope a little harder.
Cymru am byth
David Jones #9715
Cymru am byth
David Jones #9715
- Don Gale
- 356 Fan
- Posts: 1183
- Joined: Wed Jul 26, 2017 6:27 pm
- Tag: Black A's Matter
- Location: Albuquerque
- Contact:
Re: Link Pins loosen up
In lieu of VW tool 256, one could accurately measure the straightness of the trailing arms with a surface plate, height gauge, a set of Jo blocks, and a precision ground hardened round, 18mm (approx. $20 on McMaster-Carr for a 12" length). Parallelism and skew can both be measured in 2 separate setups. As for straightening, I would avoid heat, not knowing the metalurgical state the arms were forged to and subsequently heat treat. (although there are numerous shade tree shops in the south valley who skillfully momentarily apply a torch to coil springs and leaf springs to create lowriders under their own weight).
If the arm is only marginally bent, I would probably fixture it and use Al's method with a beefy chunk of steel. One can reasonably assume if bent, it was the result of a curb, pothole, or minor crash. For impact loads such as that, the yield stress is effectively doubled, in which case it would be better to straighten it with a judicious whack as opposed to steady static muscle.
If the arm is only marginally bent, I would probably fixture it and use Al's method with a beefy chunk of steel. One can reasonably assume if bent, it was the result of a curb, pothole, or minor crash. For impact loads such as that, the yield stress is effectively doubled, in which case it would be better to straighten it with a judicious whack as opposed to steady static muscle.
1958 356A 1600 Super Sunroof Coupe
former 1966 Euro 912 Sunroof
former 1978 Intermeccanica Speedster w/'68 912
Member Since 1983, #4039
"Nostalgia isn't what it used to be"
former 1966 Euro 912 Sunroof
former 1978 Intermeccanica Speedster w/'68 912
Member Since 1983, #4039
"Nostalgia isn't what it used to be"
- Vic Skirmants
- Registry Hall of Fame
- Posts: 9303
- Joined: Tue Oct 27, 2009 5:02 pm
- Location: SE Michigan
- Contact:
Re: Link Pins loosen up
David; that's pretty much as I see it. The tie rod hole was the small VW size, so all VW.David Jones wrote: ↑Wed Nov 20, 2019 2:23 pm Vic, does that mean that they just used a VW stub axle complete and the only difference at that time to a VW was the larger aluminum drum?
- Martin Benade
- 356 Fan
- Posts: 12388
- Joined: Wed Nov 23, 2011 10:52 am
- Location: Cleveland, Ohio
Re: Link Pins loosen up
Are the left and right upper arms the same?
Cleveland Ohio
62 Cabriolet
56 VW
02 IS 300
04 Sienna
62 Cabriolet
56 VW
02 IS 300
04 Sienna