Lowering Spring Plates
- Adam Wright
- Classifieds Monitor
- Posts: 10323
- Joined: Wed Mar 12, 2008 1:00 am
- Tag: KTF
Lowering Spring Plates
Anyone ever see anything like this before?
- Attachments
-
- 60518997_859505767726033_1673963044054499328_n.jpg (208.52 KiB) Viewed 1558 times
-
- 60426000_859505717726038_5630801502009294848_n.jpg (188.41 KiB) Viewed 1558 times
-
- 60393703_859505744392702_8303753679752658944_n.jpg (155.63 KiB) Viewed 1558 times
www.unobtanium-inc.com
Check out my Barn Find column in the Registry magazine, always looking for good stories.
Check out my Barn Find column in the Registry magazine, always looking for good stories.
- Martin Benade
- 356 Fan
- Posts: 12392
- Joined: Wed Nov 23, 2011 10:52 am
- Location: Cleveland, Ohio
Re: Lowering Spring Plates
No, but I bet that worked wonders for the toe-in.
Cleveland Ohio
62 Cabriolet
56 VW
02 IS 300
04 Sienna
62 Cabriolet
56 VW
02 IS 300
04 Sienna
-
- 356 Fan
- Posts: 1357
- Joined: Fri Dec 12, 2008 1:15 pm
- Location: coos bay oregon
Re: Lowering Spring Plates
If i'm looking at the picture right it looks like the dog leg bends are wrong. in on one side and out on the other. just a side note I installed some VW adjustable spring plates on mine. I wanted to lower it about an inch or so now I can adjust it were I want it. i did rotate the torsion bars 1 fine click up. i don't have it on the ground yet to see what its going to do i should have it on wheels next week.
Jay D.
Jay D.
jay darlington
- Ron LaDow
- 356 Fan
- Posts: 8100
- Joined: Wed Mar 26, 2008 11:45 am
- Location: San Francisco
Re: Lowering Spring Plates
Like about that?
For that to correct the toe, I think the lower plate has to be the right side, and has to be rotated quite a bit on the T-bar.
If it is left side, you'd have raised the car and given it a lot of toe-out.
Not sure and not willing to spend the skull-job on it this evening.
Ron LaDow
www.precisionmatters.biz
www.precisionmatters.biz
- Don Gale
- 356 Fan
- Posts: 1184
- Joined: Wed Jul 26, 2017 6:27 pm
- Tag: Black A's Matter
- Location: Albuquerque
- Contact:
Re: Lowering Spring Plates
Aren't they tempered steel? I'd be concerned with welding them lest they be prone to cracking. Can't you accomplish the same effect by clocking the inner & outer splines?
1958 356A 1600 Super Sunroof Coupe
former 1966 Euro 912 Sunroof
former 1978 Intermeccanica Speedster w/'68 912
Member Since 1983, #4039
"Nostalgia isn't what it used to be"
former 1966 Euro 912 Sunroof
former 1978 Intermeccanica Speedster w/'68 912
Member Since 1983, #4039
"Nostalgia isn't what it used to be"
-
- 356 Fan
- Posts: 2506
- Joined: Thu Mar 27, 2008 9:14 am
- Tag: Official curmudgeon
- Location: Ft Collins CO
Re: Lowering Spring Plates
I think it was a bad idea gone bad.
Shortening the wheelbase, increasing the toe-in, offsetting the centerline.
Welding spring steel.
What could possibly go wrong?
Shortening the wheelbase, increasing the toe-in, offsetting the centerline.
Welding spring steel.
What could possibly go wrong?
- Martin Benade
- 356 Fan
- Posts: 12392
- Joined: Wed Nov 23, 2011 10:52 am
- Location: Cleveland, Ohio
Re: Lowering Spring Plates
+1. Funny they are not presently being used.
Cleveland Ohio
62 Cabriolet
56 VW
02 IS 300
04 Sienna
62 Cabriolet
56 VW
02 IS 300
04 Sienna
- Greg Scallon
- 356 Fan
- Posts: 789
- Joined: Thu Mar 27, 2008 1:12 pm
- Location: Los Altos, CA
Re: Lowering Spring Plates
I think the offset you guys are seeing is an optical illusion and they are actually all in one plane, same as stock. It looks to me like they've simply been cut and re-welded. Adam?
-Greg
-Greg
'58 Speedster
'56 VW Deluxe Microbus
'56 VW Deluxe Microbus
- Vic Skirmants
- Registry Hall of Fame
- Posts: 9304
- Joined: Tue Oct 27, 2009 5:02 pm
- Location: SE Michigan
- Contact:
Re: Lowering Spring Plates
Oh, yes.Norm Miller wrote: ↑Sat May 18, 2019 12:10 am I think it was a bad idea gone bad.
Shortening the wheelbase, increasing the toe-in, offsetting the centerline.
Welding spring steel.
What could possibly go wrong?
- Jacques Lefriant
- 356 Fan
- Posts: 4668
- Joined: Mon Dec 06, 2010 1:50 pm
- Location: Washoe county NV
Re: Lowering Spring Plates
If they are shorter than stock it may be an accommodation for 901 short wheel base trailing arms
- Spencer Harris
- 356 Fan
- Posts: 1149
- Joined: Thu Mar 27, 2008 12:39 pm
- Location: San Joaquin Valley, California
Re: Lowering Spring Plates
Looks like the surgery was performed on early spring plates. '53 plates have the three-bolt pattern while '55 plates have four-bolt pattern (not sure when the change occurred).
Spencer Harris
San Joaquin Valley, CA.
San Joaquin Valley, CA.
-
- 356 Fan
- Posts: 392
- Joined: Thu Feb 23, 2017 12:41 am
- Location: So Cal
Re: Lowering Spring Plates
Is this the set that was for sale on Samba or Pelican ?
The seller was re-listing them for months, can't find them for sale now.
The seller was re-listing them for months, can't find them for sale now.
- Jim Liberty
- 356 Registry Member
- Posts: 4320
- Joined: Tue May 06, 2008 3:47 pm
- Tag: Jim
- Location: Orange Co., CA
- Contact:
Re: Lowering Spring Plates
This is one change I would never make. The cars are 60 years old, buy a 911. ……………….Jim.
Jim Liberty
- Al Zim
- 356 Fan
- Posts: 4378
- Joined: Thu Mar 27, 2008 12:37 pm
- Location: FT.WORTH/DALLAS TEXAS
- Contact:
Re: Lowering Spring Plates
What you are looking at is a dune buggy deal. I recently purchased a 901 transmission that was butchered to fit and off road buggy. al zim
www.allzim.com
356 Parts and Services
www.facebook.com/ZimsAuto/
www.instagram.com/zims_autotechnik/
356 Parts and Services
www.facebook.com/ZimsAuto/
www.instagram.com/zims_autotechnik/
-
- 356 Fan
- Posts: 669
- Joined: Wed Apr 30, 2008 7:02 am
- Location: Washington DC Area
Re: Lowering Spring Plates
Adam,
Looks like you have two very unique "door stops"
Looks like you have two very unique "door stops"