In reassembling my steering column I'm missing the three small "filester" screws which attach the turn signal assembly to the steering column. The small one, 644-347-763-05, is available, but the other two, 644-347-764-05, are NLA. The parts catalogue does not give a dimension. Does anyone know either the correct dimensions so I can perhaps source them elsewhere, or otherwise know where I might purchase these tiny little suckers?
TIA
Dimensions needed for screws attaching turn switch to clolumn
-
- 356 Fan
- Posts: 121
- Joined: Tue Apr 15, 2008 10:10 pm
- Location: Ozark Mtns
Dimensions needed for screws attaching turn switch to clolumn
Gordon Watkins
1963 356B Super Coupe w/912/SC engine
1986 911 Carrera
1963 356B Super Coupe w/912/SC engine
1986 911 Carrera
- Mike Wilson
- Classifieds Monitor
- Posts: 11492
- Joined: Tue Apr 15, 2008 4:37 pm
- Location: SW Los Angeles
Re: Dimensions needed for screws attaching turn switch to clolumn
I believe Klasse 356 has them.
Mike
Mike
Mike Wilson
Lomita, CA
'63 B coupe
Lomita, CA
'63 B coupe
-
- 356 Fan
- Posts: 197
- Joined: Sat Mar 29, 2008 1:11 pm
- Location: Texas
Re: Dimensions needed for screws attaching turn switch to clolumn
contact Doug Feistamel. He has the screws. info@type356a.com
Doug knows everything about that switch and if you get on his list he will rebuild it.
I got these screws from Doug and I'm still in the line for a switch rebuild.
Jim Learmonth
Houston, TX
65 C Coupe
Doug knows everything about that switch and if you get on his list he will rebuild it.
I got these screws from Doug and I'm still in the line for a switch rebuild.
Jim Learmonth
Houston, TX
65 C Coupe
-
- 356 Fan
- Posts: 121
- Joined: Tue Apr 15, 2008 10:10 pm
- Location: Ozark Mtns
Re: Dimensions needed for screws attaching turn switch to clolumn
I don't see 644-347-764-05 in Klasse's catalog but have inquired and will also contact type356a. Thanks for the suggestions.
Gordon Watkins
1963 356B Super Coupe w/912/SC engine
1986 911 Carrera
1963 356B Super Coupe w/912/SC engine
1986 911 Carrera
-
- 356 Fan
- Posts: 2506
- Joined: Thu Mar 27, 2008 9:14 am
- Tag: Official curmudgeon
- Location: Ft Collins CO
Re: Dimensions needed for screws attaching turn switch to clolumn
You also might check with Wolfsburg West as VW's used the same switch up to 1960.
-
- 356 Fan
- Posts: 121
- Joined: Tue Apr 15, 2008 10:10 pm
- Location: Ozark Mtns
Re: Dimensions needed for screws attaching turn switch to clolumn
Just to confirm and close this thread, both type356a and Klasse356 have these screws.
I don't think there's much of anything that can't be found with the assistance of this fine group. Thanks!
I don't think there's much of anything that can't be found with the assistance of this fine group. Thanks!
Gordon Watkins
1963 356B Super Coupe w/912/SC engine
1986 911 Carrera
1963 356B Super Coupe w/912/SC engine
1986 911 Carrera
- Mike Wilson
- Classifieds Monitor
- Posts: 11492
- Joined: Tue Apr 15, 2008 4:37 pm
- Location: SW Los Angeles
Re: Dimensions needed for screws attaching turn switch to clolumn
As always, we're glad to be of help.
Mike
Mike
Mike Wilson
Lomita, CA
'63 B coupe
Lomita, CA
'63 B coupe