'59 356 A coupe door identification
-
- 356 Fan
- Posts: 3
- Joined: Thu Dec 02, 2010 12:58 pm
'59 356 A coupe door identification
Could someone help me identify which of my doors are most correct. My drivers door handle center of push button is located approx 14 1/2" from bottom edge of door and the dished area of the door beneath the handle is about 2 3/4" across from top to bottom. My passenger door handle center of push button is approx. 15 1/8" from bottom edge of door and the dished area is about 2 7/8" across from top to bottom. What have I got here? Which is correct? Thank you!
- Thomas Fago
- 356 Fan
- Posts: 26
- Joined: Mon Nov 01, 2010 8:02 pm
Re: '59 356 A coupe door identification
My 59a coupe original drivers door 15and an eights inch an 2 and seven eights hope this helps
- Mark Cohn
- 356 Fan
- Posts: 292
- Joined: Wed Mar 26, 2008 6:29 pm
- Location: Central Texas
Re: '59 356 A coupe door identification
FWIW I measured the same distance on a Convertible D. It looks to be just under 15 inches.
- Bill Coghlan
- 356 Fan
- Posts: 159
- Joined: Tue Mar 25, 2008 10:03 pm
- Location: Rancho Mirage, CA
Re: '59 356 A coupe door identification
My '59 A driver side door measures 14 7/8" from the bottom edge to the approximate center of button - the indentation is about 2 5/8" top to bottom
-
- 356 Fan
- Posts: 3
- Joined: Thu Dec 02, 2010 12:58 pm
Re: '59 356 A coupe door identification
Thank you for the replies! Any ideas what my drivers door may have been from with the lower handle location? The inner door structure and door jam mechanisms all seem correct. Someone mentioned possibly being re skinned with an older door skin?
- Larry Coreth
- 356 Fan
- Posts: 1930
- Joined: Sun Apr 20, 2008 12:48 pm
- Location: NE N.CAROLINA
Re: '59 356 A coupe door identification
Have you checked the VIN number stamped on the inner door surface ?
In particular the last 3 digits of the VIN are stamped there
Have you got a T-1 door ?
In particular the last 3 digits of the VIN are stamped there
Have you got a T-1 door ?
Larry Coreth
Roanoake Rapids, NC
Roanoake Rapids, NC
-
- 356 Fan
- Posts: 3
- Joined: Thu Dec 02, 2010 12:58 pm
Re: '59 356 A coupe door identification
It has been a couple of years since but as I remember my drivers door with the 14 1/2" measurement last 3 digits matched up with my vin #'s. My passenger door that seems to match the dimensions of the other replies is actually a replacement with totally different #'s. That is why I am a bit stumped! Did earlier cars have lower handle locations or maybe convertibles that my door frame may have been re skinned with? Both doors with the interior panels removed are of the same T2 and up design. Thanks
-
- 356 Fan
- Posts: 318
- Joined: Sat Nov 05, 2016 11:00 pm
Re: '59 356 A coupe door identification
when looking for donor doors for a 1959, what model years would be a correct replacement?
-
- 356 Fan
- Posts: 318
- Joined: Sat Nov 05, 2016 11:00 pm
Re: '59 356 A coupe door identification
i am restoring a 1959 coupe that came with mulitple parts in a barn.
Currently have 3 doors with vent windows and two doors that are bare. (vent window doors are obviously wrong)
My VIN is 108252
the two bare doors have the number 759 on each of them.
Oddly enough, on my Kardex, it shows my build date of 1/7/59
Currently have 3 doors with vent windows and two doors that are bare. (vent window doors are obviously wrong)
My VIN is 108252
the two bare doors have the number 759 on each of them.
Oddly enough, on my Kardex, it shows my build date of 1/7/59
- John Clarke
- 356 Fan
- Posts: 2115
- Joined: Wed Aug 27, 2008 6:38 am
- Location: East Sussex, England
- Contact:
Re: '59 356 A coupe door identification
Hi all
Were our cars manufactured using the metric system? Would it be better then to use the correct metric dimensions ?
15" and how many eighths !! What? Who still uses this crazy imperial system?
Jay
Were our cars manufactured using the metric system? Would it be better then to use the correct metric dimensions ?
15" and how many eighths !! What? Who still uses this crazy imperial system?
Jay
- Wes Bender
- 356 Fan
- Posts: 4940
- Joined: Wed Aug 27, 2008 10:54 am
- Location: Somewhere in the Gadsden Purchase, USA
Re: '59 356 A coupe door identification
If the good Lord had intended us to use the metric system, he would have given us ten fingers.
.... no, wait......
.... no, wait......
Some days it's just not worth chewing through the restraints.....
- Martin Benade
- 356 Fan
- Posts: 12388
- Joined: Wed Nov 23, 2011 10:52 am
- Location: Cleveland, Ohio
Re: '59 356 A coupe door identification
Its mostly us Americans that ignant enough to use that old system... The conv D and roadsters have a completely different door so don't consider their dimensions.
Cleveland Ohio
62 Cabriolet
56 VW
02 IS 300
04 Sienna
62 Cabriolet
56 VW
02 IS 300
04 Sienna
-
- 356 Fan
- Posts: 318
- Joined: Sat Nov 05, 2016 11:00 pm
Re: '59 356 A coupe door identification
would there be much difference from a 1959 door and a 1961 door aprt from window frame?
Iam looking for doors for my 1959 restoration.
Iam looking for doors for my 1959 restoration.
-
- 356 Fan
- Posts: 318
- Joined: Sat Nov 05, 2016 11:00 pm
Re: '59 356 A coupe door identification
anybody have a picture of a 1959 coupe door on the inside with the door panel removed?
Supposedly 1958 and 1959 are the same door. (different then the early A door ineer structure)
What makes the 58/59 door different then a 1960+ door?
Supposedly 1958 and 1959 are the same door. (different then the early A door ineer structure)
What makes the 58/59 door different then a 1960+ door?
- Jim Breazeale
- Classifieds Monitor
- Posts: 2804
- Joined: Thu Mar 27, 2008 8:07 pm
- Tag: SF Giants Fan
- Location: SF Bay Area
- Contact:
Re: '59 356 A coupe door identification
58(T2) and 59(T2) Coupe doors are the same. They are way different than T1 doors that proceeded them. A T5 door is very similar but has a bit of difference at the top to support the window frame with vent windows. The T5 and T2 doors appear to have been made from the same stamping.tom collingwood wrote:anybody have a picture of a 1959 coupe door on the inside with the door panel removed?
Supposedly 1958 and 1959 are the same door. (different then the early A door ineer structure)
What makes the 58/59 door different then a 1960+ door?
Regards
Jim
Jim Breazeale
www.easypor.com
www.facebook.com/pages/European-Auto-Salvage-Yard-EASY/120458108029410
www.easypor.com
www.facebook.com/pages/European-Auto-Salvage-Yard-EASY/120458108029410