Check for oil cooler leaks, replace o rings? Check fan for loose potential grenading blades? replace oil filter flex lines and crush gaskets on the oil tee off the crankcase?

Instead of screwing around with wire on the upper engine bolt near the starter, weld a piece of rod to the head of the bolt to prevent rotation. Someone on the board was making them, but it takes less tan a minute with the mig and you'll never curse at engine removal again.

Kevin Murray
Schaumburg, IL
1954 Pre A
1961 Alfa Sprint Speciale
1935 Packard Sedan Convertible
1957 BMW Isetta (sold!)
1954 RR Silver Wraith (sold!)

I have to agree with Rick- his idea is just as important as the more car-centric ones.

_________________

david meyers wrote:
> Hello, I'm reaching out to all the 356 "Veterans", on behalf of
> first-timers like myself who could use some tips/advice, do's and don'ts, etc ,during
> or after this process.
>
> Although my 64C has given "birth" before ...and I will have a some what
> experienced "mid-wife" assisting, I'm a little nervous about being a first
> time "daddy"...like when the engine pops out , what if I don't snip the
> fuel line just right and she "bleeds" to death???
>
> okok, I know I'm sick<big grin here> I was thinking of things like throw-out
> bearing/clutch, doing both heads even though I only seem to have only one leaky
> exhaust valve ,etc,etc
> ....I just don't want to kick myself after the engine goes back in with a
> "coulda/woulda/shoulda," ....it would have been so easy and much cheaper
> while out.
>
> many thanks, in advance to, AND from the members like me,
> I haven't seen any threads on this subject , or are there?
> david

Dave,
Get behind the wheel and make motor sounds and pretend your shifting that way you wont miss not being able to drive it while the motor is out.

Back under my rock I go
Bob Lee
346 Registry member 16135
356 Club of SC
912 Registry member 5888-R

_________________

You can buy a bolt replacement..for one of the engine bolts... replace the one that you have to snake your arm up over the transmission.
One of the vendors / guys on this list makes & sells a custom bolt... it won't turn as you take the nut off with a long wrench down the back side between the trans and engine.
... this bolt replacment is money-in-the bank (trust me).

Tom
www.project356.com

_________________
Tom Hudson
'63 Euro Coupe
www.project356.com
www.project356.com/bmw

When doing the trans mounts, it is only two more bolts to remove the hoop and give it a good cleaning. Makes the area look neat and tidy.

_________________
Paul Hatfield
"Miss April"
http://www.enginesinback.com

Paul!!!
You'll never get the engine back in with the upper bolts in wrong!!!

OK, I see you changed the photo. To avoid confusing others, that is correct.
Carry on.

_________________

Ok Eagle-Eye! That was years ago and I forgot that I later changed the orientation.
Jez- Can't get anything by you.
Paul

_________________
Paul Hatfield
"Miss April"
http://www.enginesinback.com

Paul- What Vic means is that the upper through bolts that hold the trans mounts to the trans are installed incorrectly. The head needs to be inside the bell housing and the nut outside bearing against the mount. The flywheel will interfere with the bolts the way you have it now.

_________________
'55 Cab 1300 Super Race Car
'57 Speedster
'59 Sunroof
'60 Devin D Race Car-in process
'63 GS 2133 coupe
'67 S Original Owner

Yes, it is changed. See my post above.

_________________
Paul Hatfield
"Miss April"
http://www.enginesinback.com

Nag, nag, nag.

_________________

Hi, I am a first timer too and at this time my engine ist out. I have to remove all insulation in engine and luggage compartment. My question is, where can I find equally insulation quality for replacement?

Check the Classified section. I think "The Parts Shop" has it.

_________________

I've got to remember to do that this time. I usually use vice grips on the driver's side and get by with just fiddling on the passenger side.

_________________
Matthew Devereux
'08 Cayman S
'58 356A coupe
'70 911E project
1995 993 Polar Silver/Chestnut - sold

This parts are to expensive, building an outlaw and no concours winner. Thank you anyway for your reply.

Anybody with cheaper solution?

I assume my top two bolts are backwards then? Or did Paul change his picture? To think I just stumbled on this post, likely saved me hours!! Thanks!

_________________