What To Do While the Engine is Out Of the Car?
-
- 356 Fan
- Posts: 178
- Joined: Sat May 17, 2008 3:49 pm
- Location: Schaumburg, IL
Re: What To Do While the Engine is Out Of the Car?
Check for oil cooler leaks, replace o rings? Check fan for loose potential grenading blades? replace oil filter flex lines and crush gaskets on the oil tee off the crankcase?
Instead of screwing around with wire on the upper engine bolt near the starter, weld a piece of rod to the head of the bolt to prevent rotation. Someone on the board was making them, but it takes less tan a minute with the mig and you'll never curse at engine removal again.
Kevin Murray
Schaumburg, IL
1954 Pre A
1961 Alfa Sprint Speciale
1935 Packard Sedan Convertible
1957 BMW Isetta (sold!)
1954 RR Silver Wraith (sold!)
Instead of screwing around with wire on the upper engine bolt near the starter, weld a piece of rod to the head of the bolt to prevent rotation. Someone on the board was making them, but it takes less tan a minute with the mig and you'll never curse at engine removal again.
Kevin Murray
Schaumburg, IL
1954 Pre A
1961 Alfa Sprint Speciale
1935 Packard Sedan Convertible
1957 BMW Isetta (sold!)
1954 RR Silver Wraith (sold!)
- Martin Benade
- 356 Fan
- Posts: 12353
- Joined: Wed Nov 23, 2011 10:52 am
- Location: Cleveland, Ohio
Re: What To Do While the Engine is Out Of the Car?
I have to agree with Rick- his idea is just as important as the more car-centric ones.
Cleveland Ohio
62 Cabriolet
56 VW
02 IS 300
04 Sienna
62 Cabriolet
56 VW
02 IS 300
04 Sienna
- Bob Lee
- 356 Fan
- Posts: 259
- Joined: Thu Mar 27, 2008 12:45 pm
- Location: USA
Re: What To Do While the Engine is Out Of the Car?
david meyers wrote:
> Hello, I'm reaching out to all the 356 "Veterans", on behalf of
> first-timers like myself who could use some tips/advice, do's and don'ts, etc ,during
> or after this process.
>
> Although my 64C has given "birth" before ...and I will have a some what
> experienced "mid-wife" assisting, I'm a little nervous about being a first
> time "daddy"...like when the engine pops out , what if I don't snip the
> fuel line just right and she "bleeds" to death???
>
> okok, I know I'm sick<big grin here> I was thinking of things like throw-out
> bearing/clutch, doing both heads even though I only seem to have only one leaky
> exhaust valve ,etc,etc
> ....I just don't want to kick myself after the engine goes back in with a
> "coulda/woulda/shoulda," ....it would have been so easy and much cheaper
> while out.
>
> many thanks, in advance to, AND from the members like me,
> I haven't seen any threads on this subject , or are there?
> david
Dave,
Get behind the wheel and make motor sounds and pretend your shifting that way you wont miss not being able to drive it while the motor is out.
Back under my rock I go
Bob Lee
346 Registry member 16135
356 Club of SC
912 Registry member 5888-R
> Hello, I'm reaching out to all the 356 "Veterans", on behalf of
> first-timers like myself who could use some tips/advice, do's and don'ts, etc ,during
> or after this process.
>
> Although my 64C has given "birth" before ...and I will have a some what
> experienced "mid-wife" assisting, I'm a little nervous about being a first
> time "daddy"...like when the engine pops out , what if I don't snip the
> fuel line just right and she "bleeds" to death???
>
> okok, I know I'm sick<big grin here> I was thinking of things like throw-out
> bearing/clutch, doing both heads even though I only seem to have only one leaky
> exhaust valve ,etc,etc
> ....I just don't want to kick myself after the engine goes back in with a
> "coulda/woulda/shoulda," ....it would have been so easy and much cheaper
> while out.
>
> many thanks, in advance to, AND from the members like me,
> I haven't seen any threads on this subject , or are there?
> david
Dave,
Get behind the wheel and make motor sounds and pretend your shifting that way you wont miss not being able to drive it while the motor is out.
Back under my rock I go
Bob Lee
346 Registry member 16135
356 Club of SC
912 Registry member 5888-R
- Tom Hudson
- 356 Fan
- Posts: 10
- Joined: Wed Mar 26, 2008 1:12 pm
- Location: mid Michigan
- Contact:
Re: What To Do While the Engine is Out Of the Car?
You can buy a bolt replacement..for one of the engine bolts... replace the one that you have to snake your arm up over the transmission.
One of the vendors / guys on this list makes & sells a custom bolt... it won't turn as you take the nut off with a long wrench down the back side between the trans and engine.
... this bolt replacment is money-in-the bank (trust me).
Tom
www.project356.com
One of the vendors / guys on this list makes & sells a custom bolt... it won't turn as you take the nut off with a long wrench down the back side between the trans and engine.
... this bolt replacment is money-in-the bank (trust me).
Tom
www.project356.com
Tom Hudson
'63 Euro Coupe
www.project356.com
www.project356.com/bmw
'63 Euro Coupe
www.project356.com
www.project356.com/bmw
- Paul Hatfield
- 356 Registry Member
- Posts: 1149
- Joined: Tue Mar 25, 2008 5:46 pm
- Location: Washington State
- Contact:
Re: What To Do While the Engine is Out Of the Car?
When doing the trans mounts, it is only two more bolts to remove the hoop and give it a good cleaning. Makes the area look neat and tidy.
Last edited by Paul Hatfield on Tue Jan 21, 2014 4:47 pm, edited 1 time in total.
Paul Hatfield
"Miss April"
http://www.enginesinback.com
"Miss April"
http://www.enginesinback.com
- Vic Skirmants
- Registry Hall of Fame
- Posts: 9300
- Joined: Tue Oct 27, 2009 5:02 pm
- Location: SE Michigan
- Contact:
Re: What To Do While the Engine is Out Of the Car?
Paul!!!
You'll never get the engine back in with the upper bolts in wrong!!!
OK, I see you changed the photo. To avoid confusing others, that is correct.
Carry on.
You'll never get the engine back in with the upper bolts in wrong!!!
OK, I see you changed the photo. To avoid confusing others, that is correct.
Carry on.
Last edited by Vic Skirmants on Tue Nov 04, 2014 8:29 am, edited 1 time in total.
- Paul Hatfield
- 356 Registry Member
- Posts: 1149
- Joined: Tue Mar 25, 2008 5:46 pm
- Location: Washington State
- Contact:
Re: What To Do While the Engine is Out Of the Car?
Ok Eagle-Eye! That was years ago and I forgot that I later changed the orientation.
Jez- Can't get anything by you.
Paul
Jez- Can't get anything by you.
Paul
Last edited by Paul Hatfield on Tue Jan 21, 2014 4:47 pm, edited 1 time in total.
Paul Hatfield
"Miss April"
http://www.enginesinback.com
"Miss April"
http://www.enginesinback.com
- C J Murray
- 356 Fan
- Posts: 9223
- Joined: Fri Oct 23, 2009 7:24 pm
- Location: 30MI WEST OF PHILA
- Contact:
Re: What To Do While the Engine is Out Of the Car?
Paul- What Vic means is that the upper through bolts that hold the trans mounts to the trans are installed incorrectly. The head needs to be inside the bell housing and the nut outside bearing against the mount. The flywheel will interfere with the bolts the way you have it now.
'57 Speedster
'59 Sunroof
'60 Devin D Porsche Race Car
'63 Cabriolet "Norm"
'67 911 S Original Owner
'03 Ferrari 575M
'09 Smart Passion
'59 Sunroof
'60 Devin D Porsche Race Car
'63 Cabriolet "Norm"
'67 911 S Original Owner
'03 Ferrari 575M
'09 Smart Passion
- Paul Hatfield
- 356 Registry Member
- Posts: 1149
- Joined: Tue Mar 25, 2008 5:46 pm
- Location: Washington State
- Contact:
Re: What To Do While the Engine is Out Of the Car?
Yes, it is changed. See my post above.
Paul Hatfield
"Miss April"
http://www.enginesinback.com
"Miss April"
http://www.enginesinback.com
- Vic Skirmants
- Registry Hall of Fame
- Posts: 9300
- Joined: Tue Oct 27, 2009 5:02 pm
- Location: SE Michigan
- Contact:
Re: What To Do While the Engine is Out Of the Car?
Nag, nag, nag.
-
- 356 Fan
- Posts: 2
- Joined: Tue May 21, 2013 2:19 pm
Re: What To Do While the Engine is Out Of the Car?
Hi, I am a first timer too and at this time my engine ist out. I have to remove all insulation in engine and luggage compartment. My question is, where can I find equally insulation quality for replacement?Roger Shapiro wrote:Let's sub title this thread "what is not so easy with engine IN the car"
First choice - get those two upper bolts to stay in place whilst replacing the engine. Hose clamp and glue, weld on washer, wire the two bolts to the trans housing.
Second - install a full flow oil filter - you will never regret it.
Thirdly - redo the engine walls with new "insulation." It is a definite PITA to do with the engine in.
Hope I'm not to late
Roger Shapiro
- Vic Skirmants
- Registry Hall of Fame
- Posts: 9300
- Joined: Tue Oct 27, 2009 5:02 pm
- Location: SE Michigan
- Contact:
Re: What To Do While the Engine is Out Of the Car?
Check the Classified section. I think "The Parts Shop" has it.
- Matthew Devereux
- 356 Fan
- Posts: 1047
- Joined: Sun Nov 21, 2010 11:36 am
- Location: Alberta
Re: What To Do While the Engine is Out Of the Car?
I've got to remember to do that this time. I usually use vice grips on the driver's side and get by with just fiddling on the passenger side.Kevin Murray wrote:....Instead of screwing around with wire on the upper engine bolt near the starter, weld a piece of rod to the head of the bolt to prevent rotation. Someone on the board was making them, but it takes less tan a minute with the mig and you'll never curse at engine removal again.....
Matthew Devereux
'00 Boxster S
'58 356A coupe
'00 Boxster S
'58 356A coupe
-
- 356 Fan
- Posts: 2
- Joined: Tue May 21, 2013 2:19 pm
Re: What To Do While the Engine is Out Of the Car?
vic skirmants wrote:Check the Classified section. I think "The Parts Shop" has it.
This parts are to expensive, building an outlaw and no concours winner. Thank you anyway for your reply.
Anybody with cheaper solution?
- Nathan Ward
- 356 Fan
- Posts: 56
- Joined: Sat Oct 23, 2010 5:06 pm
Re: What To Do While the Engine is Out Of the Car?
vic skirmants wrote:Paul!!!
You'll never get the engine back in with the upper bolts in wrong!!!
I assume my top two bolts are backwards then? Or did Paul change his picture? To think I just stumbled on this post, likely saved me hours!! Thanks!